Abstract:Most newly developed oil fields worldwide are ultralow permeability reservoirs, especially the Bakken and Eagle in North America as well as the Erdos and Jimusar in China. Therefore, the technology of stimulated reservoir volume (SRV) has become a critical method to improve hydrocarbon production. However, field operations in the winter season are usually confronted with numerous difficulties. For instance, conventional water-based fracturing fluid and liquid additives are easy to freeze up, and therefore, the gelation performance will be compromised. Accordingly, based on the application performance analysis of current antifreeze additive application status in many fields, several different inorganic salts and alcohols as antifreeze additives were selected. In this study, the formula of the antifreeze fracturing fluid system was designed and optimized based on the evaluations of the addition of different types of antifreeze candidates on the fracturing fluid performance. Results showed that when the environmental temperature was above −15 °C, alcohols (e.g., tetraethylene glycol) and inorganic salts with low concentrations could be employed as an antifreeze and they had nearly no negative effect on the viscosity and the cross-linking performance of the fracturing fluid. In this circumstance, the optimum composition was 0.2% hydrocarbon propyl guar gum, 0.2% borax, 1%MJ-1, and 0.5% tetraethylene glycol. In addition, when the environmental temperature is below −20 °C, the freezing resistance in the aqueous solution of alcohols was limited. At this time, NaCl with mass ratio higher than 15% showed the best antifreezing effect. However, the large amount of addition of inorganic salts would significantly reduce the viscosity of the fracturing fluid. The optimal concentration of guar gum in the antifreeze fracturing fluid system should increase to 0.4%, and the optimal concentration of borax was 0.3%. In addition, 0.1–0.5% tetraethylene glycol can also be used as an antifreeze if the operation time is less than 6 h. The development of this antifreeze fracturing fluid can further elongate the current fracturing time in winter. Moreover, the experimental results can provide a guide for the field fracturing fluid operation and application.This article has not yet been cited by other publications.

Synthesis and quantitative structure–activity relationship of unsaturated fatty acid amide propyl dimethyl tertiary amines and their application in clean fracturing fluid thickener in low temperature environment

JIN Zhiyuan1,2, SHAN Guorong2,3, PAN Pengju2,3

Preparation and Properties of Temperature Resistant and Salt Resistant Lotion Fracturing Fluid Thickener

Development of Antifreeze Fracturing Fluid Systems for Tight Petroleum Reservoir Stimulations

Novel hydraulic fracturing fluids with improved proppant carrying capacity and pH-adjustable proppant deposition behavior

Comparative Studies on Hydraulic Fracturing Fluids for High-Temperature and High-Salt Oil Reservoirs: Synthetic Polymer Versus Guar Gum

Fracturing Fluid Polymer Thickener with Superior Temperature, Salt and Shear Resistance Properties from the Synergistic Effect of Double-Tail Hydrophobic Monomer and Nonionic Polymerizable Surfactant

Effect of chemical additives on the stability and performance of suspended-emulsion fracturing fluid formed by associative thickener

Synthesis and evaluation of water-soluble fracturing fluid thickener based on hydrophobic association

Rheological Behavior of a Novel Fracturing Fluid Formed from Amine Oxide Surfactants

Preparation and performance evaluation of a low‐damage fracturing fluid for unconventional reservoirs

Performance Evaluation and Site Application of a Hydrophobic Long-Chain Ester-Based CO2 Fracturing Fluid Thickener

Synthesis and evaluation of salt tolerant delayed-crosslinking fracturing fluid system in ultra-deep high temperature wells

Ultra-deep reservoirs gel fracturing fluid with stepwise reinforcement network from supramolecular force to chemical crosslinking

Investigation of a hydrophobically associating polymer’s temperature and salt resistance for fracturing fluid thickener

Preparation and Rheological Properties of Acrylamide-based Penta-polymer for Ultra-high Temperature Fracturing Fluid

Synthesis and properties of fluorinated hydrophobic association polyacrylamide as thickener for hydraulic fracturing fluid

Design, synthesis and properties evaluation of emulsified viscosity reducers with temperature tolerance and salt resistance for heavy oil

Fe 3+ -crosslinked alkyl phosphate ester as thickener for oil-based fracturing fluids

Synthesis and Application of a Novel Multi-Branched Block Polyether Low-Temperature Demulsifier

Study on pH-Responsive Delayed, Cross-Linking and Weighted Fracturing Fluid