Abstract:Small size and high efficiency of micro gas turbines require a higher surface-to-volume ratio of recuperators. Conventional recuperators can achieve a range of 250–3600 m 2 /m 3 . Advances in materials and manufacturing, such as metal foams, can increase significantly the exchange surface and improve compactness ranging approximately from 500 to over 10,000 m 2 /m 3 , due to their exceptional micro geometry. The main advantage is that the increase of surface area does not impact the cost of the heat exchanger as much as conventional recuperators due to their easy manufacturing. This work addresses the optimisation of the recuperator using multiple objectives satisfying efficiency, power output and weight criteria, offering a holistic approach that takes into account the entire system rather than individual components or channels. A model is developed to represent the performance of a compact heat exchanger in micro gas turbines. The recuperator is an annular heat exchanger with involute profile filled with porous media in a counterflow arrangement on the hot and cold sides. The model allows the evaluation of the effect of the recuperator geometry features on the electrical efficiency, power output and weight savings in a micro gas turbine. Existing models for the global heat transfer coefficient, effective thermal conductivity, surface area and pressure drop of porous media are selected and implemented. The design variables of multi-objective are the pore density, porosity and number of channels, whilst the objectives are the overall electrical efficiency, power output and recuperator weight. The problem is solved using the Non-Dominated Sorting Genetic Algorithm (NSGA-II) to determine an approximation of the Pareto front, whilst the accuracy of the approximation is assessed against the solution obtained by an exhaustive search. The comparison shows that NSGA-II outperforms an exhaustive search by at least 90 % in terms of computational efficiency. These results allow the quantification of the impact of metal foam technology on performance metrics of the recuperator as well as the entire system. This quantitative analysis provides valuable insights into the behaviour of metal foam recuperators in micro gas turbines. An optimal design with 30 % efficiency and 28 kW power output appears in pore densities of approximately 10 and 20 pores per inch (PPI) for the air and gas side respectively, and a porosity of 85 %, which leads to a state-of-the-art recuperator weight of 48 kg. The efficiency improvement over the industry standard is 15 %, with only a 2.5 % reduction in power output.

Research on performance of micro gas turbine recuperator: A review

Recuperators for Micro Gas Turbines: A Review

Investigation on Recuperator Performance Variation into Gas Turbine

Solar Hybrid Steam-Injected Gas Turbine System with Novel Heat and Water Recovery

Finite Element Analysis of Stress on Cross-Wavy Primary Surface Recuperator Based on Thermal-Structural Coupling Model

PERFORMANCE COMPARISON OF GAS TURBINE CYCLE COMBINED WITH SUPERCRITICAL CO2 RECOMPRESSION AND REGENERATIVE CYCLE

Experimental Study on the Off-Design Performances of a Micro Humid Air Turbine Cycle: Thermodynamics, Emissions and Heat Exchange

The application characteristics of plate-fin recuperator for HTGR

Performance of simple/recuperation cycle gas turbines under variable conditions

A study on dynamic characteristics of plate-fin recuperator in high-temperature gas-cooled reactor closed cycle

Dynamic Modeling for Compact Recuperator in Helium Gas Turbine Direct-Cycle System

Evaluation , Comparison and Optimization of the Compact Recuperator for the High Temperature Gas-Cooled Reactor ( HTGR ) Helium Turbine System

Optimized Design of the Volute Between Turbine and Regenerator in Micro Gas Turbine

Thermodynamic analysis of a gas turbine cycle with direct recuperation based on a multistage compressed mass storage process

Metal foam recuperators on micro gas turbines: Multi-objective optimisation of efficiency, power and weight

Performance evaluation of heater and recuperator in Brayton cycles for power and energy storage

Analysis on the development of micro gas turbine generation technology

A Review of the Efficiency Improvement of Hydraulic Turbines in Energy Recovery

Research on the effectiveness of the key components in the HAT cycle

Recuperation of Aircraft Gas Turbine Engines to Solve Problems Land Transport and Energy

Numerical Study of the Influence of Different Bending Shapes on the Heat Transfer Characteristics of Annular Cross Wavy Primary Surface Recuperator (CW-PSR)