Abstract:A n-butanol/diesel spray test system was constructed to conduct common rail bench test and constant volume bomb experiments in present work to investigate the impact of different n-butanol blending ratios on spray characteristics and the spray evolution process. To be specific, the research was carried out under the n-butanol blending ratios ofwith 0, 10%, 20%and 40% respectively to study various n-butanol blending ratio effects and to analyze the variation of the physical and chemical characteristics of the fuel. Then, the fuel spray patterns data at 0.4 ms was carefully collected and analyzed to compar the effect of different n-butanol blending ratios on spray penetration and spray angle. In addition, an-butanol/diesel spray model in engine cylinder was also established, to analyze how spray penetration and SMD of blended fuel varied during spray process, , as well as the impacts of n-butanol blending ratios on evaporation characteristics of blended fuel. Furthermore the various changes in velocity field and number density field in spray processes with different blending ratios have been taken into consideration and discussed for more detailed problems. It can be observed from the research data that: in normal temperature and pressure region,as the n-butanol blending ratio increased,the spray penetration decreased and there was a moderate rise in spray angle during spray process; as blending ratios of n-butanol increased by 40%, the spray penetration slightly reduced by 4.95%while reversely the spray angle climbed by 16.7%. Also when the injection pressure ascended, there was obvious rise both in the spray penetration and spray angle, particularly, if injection pressure rose by 40 MPa , the spray angle increased by 28.43°. During the spray evolution process, the n-butanol blending ratios influenced the spray penetration slightly, while in the very initial step of fuel blending process, the higher the n-butanol blending ratio was, the smaller SMD of blended fuel became. Along with the development of the spray process, however, the ultimate spray penetrations of different blended fuel were basically the same. In the injecting duration period, with the increasing of n-butanol blending ratio, there was a substantial drop in the mass of the fuel injected into the cylinder, and the peak velocity value of the jet dropped distinctly. Moreover, as a result of the fall in the viscosity and surface tension, the volatilization of blended fuel was apparently enhanced and subsequently fuel evaporation mass was increased slightly. The n-butanol blending ratios had quite limited impact on number density of drops but obviously facilitated the spray period, that is, the larger the blend ratio was, the better the spray characteristics would be. Besides this, in the central region of the downstream jet the figure of number density reached the highest.

Experimental study on spray impingement during diesel engine starting

Experimental Analysis in Dynamics Characteristics of Impinging Spray by a PFI Injector : from Spray Atomization to Fuel Adhesion Formation

Visualization on spray and flame characteristics of wall-impinging spray under marine diesel engine conditions

Experimental study on microscopic characteristics of impinging spray at elevated ambient pressure conditions during development

Wall-impinging laminar premixed n-dodecane flames under autoignitive conditions

An Experimental and Numerical Study of Diesel Spray Impingement on a Flat Plate

Microscopic Level Study on the Spray Impingement Process and Characteristics

Effect of wall-impingement distance on fuel adhesion characteristics of split injection spray under cross-flow condition

Numerical study of wall cooling effects on diesel spray combustion characteristics under different ambient conditions

Experimental and numerical studies on fuel-film combustion and wall thermal effect of diesel spray

Optical experiments on diesel knock for high altitude engines under spray impingement conditions

Spray and dynamic heat transfer induced by 2-methylfuran transient spray impingement on piston surface

Experimental Study on the Adhesive Fuel Features of Inclined Wall-Impinging Spray at Various Injection Pressure Levels in a Cross-Flow Field

New Insights into Abnormal Combustion Phenomena Induced by Diesel Spray-Wall Impingement under Engine-Relevant Conditions

Visualization Research of the Gasoline Spray-wall Interaction and Wall Film Formation and Numerical Simulation

Optical and numerical study on the effect of wall impingement on passive jet ignition characteristics of methane/air mixture

Experimental Study on the Macroscopic Characteristics of Air-Assisted Diesel Spray

Spray behavior of butanol-diesel and numerical simulation of mixture formation with engine

Visualization and simulation study on impacts of wall roughness on spray characteristics of ducted fuel injection

Wall Temperature Effects on Ignition Characteristics of Liquid-phase Spray Impingement for Heavy-duty Diesel Engine at Low Temperatures

Experiment investigation on the effects of air assisted SCR spray impingement on wall temperature evolution