Abstract:As a key component of a reversible pump-turbine unit, a pump-turbine runner rotates at two opposite directions under the pump and turbine modes. The flow states in the runner are quite different under the pump and turbine modes, which creates a great challenge for the design of a pump-turbine runner. Nowadays, a pump-turbine runner is always designed in one mode and verified with the other mode. Since there are several parameters affecting the runner’s performances and one parameter might have contrary effects on runner performances under the pump and turbine modes, it is hard to obtain a runner with high performance at both the pump and turbine modes by a trial and error method. In the present paper, a 3D inverse design method, CFD calculations, and multi-objective optimization strategy were coupled, and an optimal design system was built to improve the performances of a reversible pump-turbine runner. In the system, by using a 3D inverse design method, the runner shape was obtained by inputting corresponding parameters. A validated CFD method was used to estimate runner performances under different operating conditions. A multi-objective optimization strategy was then adopted to search runners with good performances at both operating modes in the design space based on a response surface model between input parameters and runner performances. The optimal design system was capable of solving some difficulties in pump-turbine runner design, such as a long design cycle and difficulties in obtaining good performances at both pump and turbine modes. The system was used to optimally design a middle-high head reversible pump-turbine runner, in which blade loading and blade lean were chosen as the input parameters, runner efficiency at the pump design point and the turbine rated point were set as optimization objectives, and the head at pump design point was set as a constraint. Since the optimization calculations were based on a response surface model, performances of nearly 10 000 runners under different operating modes were estimated in several minutes. Three runners from the Pareto frontier were chosen for detailed validation. CFD results showed that the optimal runner had a high hydraulic efficiency of over 95% at both the pump and turbine modes, which indicated a great improvement in runner efficiency in the turbine mode and the maintenance of high efficiency at the pump mode as compared with the initial design. The effects of the input parameters on runner interior characteristics under different operating modes were also analyzed in this paper. The results showed that fore-loaded blade loading distribution on the shroud was helpful in improving the flow state at the inlet under the pump mode by reducing the low-pressure area on the suction side. The blade lean at the high pressure side not only changed the work distribution along the span wise direction, but also improved the flow state by bringing down the pressure difference at the inlet in the turbine mode, and played an important role in improving runner efficiency, especially in the turbine mode.

Effect of circumferential lean of pump-turbine runner blades on energy characteristics

Effect of 3D Shape of Pump-Turbine Runner Blade on Flow Characteristics in Turbine Mode

Study on the Effects of Runner Geometries on the Performance of Inline Cross-Flow Turbine Used in Water Pipelines

Investigation on Flow Characteristics of Pump-Turbine Runners with Large Blade Lean

Development Of A Pump-Turbine Runner Based On Multiobjective Optimization

Optimal design of reversible pump-turbine runner

Unstable Flow Characteristics in Vaneless Region with Emphasis on the Rotor-Stator Interaction for a Pump Turbine at Pump Mode Using Large Runner Blade Lean

The Effect of the Nozzle Blade Pitch on the Velocity Coefficient of the Inflow Turbine with Partial Bladings of the Runner

Optimization Design of a Reversible Pump–turbine Runner with High Efficiency and Stability

Research and optimization of performances of a pump turbine in pump mode

Multi-objective Optimization Design on High Pressure Side of a Pump-Turbine Runner with High Efficiency

Enhancing operational stability of a reversible pump-turbine through blade lean design

Broadening the operating range of pump-turbine to deep-part load by runner optimization

Numerical Study on the Impact of Runner Inlet Arc Angle on the Performance of Inline Cross-Flow Turbine Used in Urban Water Mains

Strategies employed in the design and optimization of pump as turbine runner

Hydraulic development of high specific-speed pump-turbines by means of an inverse design method, numerical flow-simulation (CFD) and model testing

Optimization of the Runner for Extremely Low Head Bidirectional Tidal Bulb Turbine

Multiobjective optimization design of ultrahigh-head pump turbine runners with splitter blades

Influence of Blade Leaning on Hydraulic Excitation and Structural Response of a Reversible Pump Turbine

The effect of runner blade loading on the performance and internal flow of a Francis hydro turbine model

Optimization of geometric parameters of hydraulic turbine runner in turbine mode based on the orthogonal test method and CFD