Abstract:The Hydrogen production plays important role as part of energy transition strategy in Germany as well as in visions and subsequent policy of European Green Deal activities. Schaeffler [1] is driving further technological development with strong financial backing of European (CHP) and German funding (H2Giga). PEM water electrolysis is regarded as powerful technology, bringing advantages of limited installation footprint, broad range of operating conditions, especially in terms of dynamic load range and featuring high efficiency between 75-90% (based on HHV) [2]. Minimizing the Levelized Cost of Hydrogen demands reduction in CAPEX, OPEX, maintenance whilst extending lifetime to secure full Return of Investment [3]. In addition, production of green hydrogen needs to anticipate the intermittent and distributed nature of renewable energy sources whilst functioning in a decentralized energy distribution network. Enabling maximum uptime sets high demands on the stack performance requirements and its material specifications. Here we show examples of how component development and design iterations make a huge impact on the commercial viability of electrolysers in industrial applications. Efficiency is key when converting renewable electricity and water into green hydrogen and other chemicals, even though PEM electrolyser stack technology is deemed capable of increasing current densities up to 10 A/cm 2 . Therefore, State-of-Art commercial stacks are rated at current densities between ~1-3 A/cm 2 , but this anticipated trend to increase power density underlines the necessity to reduce the total electrical resistance and avoid Ohm’s losses. Critical to success is selecting materials that can sustain functionality, stability and compatibility within an operational window being pushed to higher current density to increase stack output, whilst reducing PGM content and overall cost. Progress has been achieved by combining formed metal components with durable, conductive coatings, and establishing optimum compression. Most promising results published in open literature are based on small cells on laboratory scale (5-25 cm 2 active area). So-called “screeners” are ideally suited for studying phenomena under well-controlled conditions with a plethora of diagnostic tools. In contrast, large-area stacks operated in the field don’t always operate under ideal operating conditions and can show variability in performance characteristics that escalate into unexpected degradation issues. Of course, stack behavior is dependent on its local environment within the BOP system, relative to its peers. We show how continuous remote monitoring during operation helps identify non-uniform stack operation and flag off-spec conditions, which could form the basis of Accelerated Stress Tests for testing in the laboratory. In this work we estimate how much stack technology can be improved further by forming BPP metal structures and optimizing the component design using CFD. Especially when scaling stack hardware to larger capacity, there is much emphasis on enhanced thermal management to avoid hot-spots and mitigate non-uniform degradation mechanisms and premature stack failure. Simulation results will show how flow designs could be adapted maintain uniform conditions when scaling up the active area or adding more cells to the stack. Robust Stacks are demanded for market ramp-up, demonstrating predictable performance over a long lifetime and insensitivity to a wide range of possible operating conditions. However, but to the best of our knowledge, no component- nor stack- supplier is willing to provide extensive guarantees. Fortunately, stacks quality can be improved significantly by strong automotive and manufacturing industries stepping into the PEM electrolyzer arena and introducing their automated assembly, mature manufacturing and controlled processes to guarantee reproducibility, tight tolerances, superior quality and support supply chain development. Before ramping up global production capacity massively, all players would benefit from standardizing general geometric specifications of stacks so we can leverage a stronger collective learning curve with increasing numbers. References [1] K. Rosenfeld, The Stern Stewart Institute, periodical #27 (2023) 20-27. [2] Y. Wang et.al., Energy Environ. Sci., 15 (2022) 2288-2328. [3] P. Lyubarskyy, interview: Imagining a Hydrogen-Powered Future Thanks to Simulation (2023). [4] J. Proost, Int. J. of Hydrogen Energy 44 (2019), 4406 – 4413. Figure 1

Diffusion-Bonded Unitized Anode Assemblies for PEM Electrolysis Stacks

(Invited) Manufacturing Challenges, Opportunities, And Successes for PEM Electrolysis at Scale

(Digital Presentation) Large–Scale High-Performance Low Catalyst Loaded Membrane Electrode Assemblies for Advanced Proton Exchange Membrane Water Electrolyzers

Pathways Toward Efficient and Durable Anion Exchange Membrane Water Electrolyzers Enabled By Electro‐Active Porous Transport Layers

(Invited) Progress and Perspective Towards Low-Cost High-Performance Anion Exchange Membrane Water Electrolysis

(Invited) Novel Design of Low-Loaded Membrane Electrode Assemblies for Advanced Low-Temperature Water Electrolyzers

High Performance Anion Exchange Membrane Electrolysis Using Plasma-Sprayed, Non-Precious-Metal Electrodes

Additive Manufacturing of Liquid/Gas Diffusion Layers for Low-Cost and High-Efficiency Hydrogen Production

Porous Transport Layers for Proton Exchange Membrane Electrolysis Under Extreme Conditions of Current Density, Temperature, and Pressure

A novel PEMEC with 3D printed non-conductive bipolar plate for low-cost hydrogen production from water electrolysis

A New Design of a Microfluidic Experimental Cell for the Study of Two-Phase Flow inside a PEM Water Electrolyzer

Reactive Spray Deposition Technology for Deposition of Protective Metal Layers on Porous Transport Layers in PEM Water Electrolyzers

Comprehensive study and optimization of membrane electrode assembly structural composition in proton exchange membrane water electrolyzer

(Invited) Industrialization of PEM Electrolyzer Stack Platforms: Driving Lab-Scale Innovation to Multi-MW Implementation

Bipolar plate development with additive manufacturing and protective coating for durable and high-efficiency hydrogen production

Additive manufactured bipolar plate for high-efficiency hydrogen production in proton exchange membrane electrolyzer cells

Influence of Microporous Layers on Interfacial Properties, Oxygen Flow Distribution, and Durability of Proton Exchange Membrane Water Electrolyzers

Understanding Proton Exchange Membrane Water Electrolyzer Hydrogen Crossover Mitigation in Reactive Spray Deposition Technology Fabricated Dual Recombination Layers through Distribution of Relaxation Times Analysis

(Invited) Water Electrolyzers for Green Hydrogen Production - a Tutorial on Catalyst and Electrode Development for Next Generation Devices

Modelling of a Proton-Exchange Membrane Electrolysis Cell with Liquid-Fed Cathode

Additive manufacturing of bipolar plates for hydrogen production in proton exchange membrane water electrolysis cells