Abstract:Heat transfer analysis for the compression hydrogen storage tank (CHST) during the charge–discharge cycle is necessary to ensure quick and safe refueling for fuel cell vehicles. In this paper, a dual‐zone dual‐temperature (DZDT) model for a CHST during the charge–discharge cycle process is established. The constant/variable mass flow rates and heat transfer coefficients (HTCs) are combined to form three methods. Method 1 uses constant mass flow rate and constant HTC. Method 2 uses variable mass flow rate and variable HTC calculated through the energy conservation equation. Method 3 uses variable mass flow rate and variable HTC calculated through the empirical equation. Then, these methods are applied to the DZDT model for heat transfer analysis in three cases. Research shows that for the charging process, the simulated hydrogen temperatures by Method 2 agree well with experiment data for three CHSTs. Method 1 has a maximum error of about 20°C for 19 L CHST, 15°C for 29 L CHST, and 25°C for 40 L CHST. The error of Method 3 is between Methods 1 and 2. The simulated hydrogen pressures by Methods 2 and 3 agree well with the experimental data, while Method 1 has a maximum error of about 5 MPa for 19 L CHST, 10 MPa for 29 L CHST, and 3 MPa for 40 L CHST. For the discharge process, the simulated hydrogen temperatures by Methods 2 and 3 have a relatively slight difference with the experimental data, while Method 1 has relatively significant differences for three CHSTs. Only slight differences exist between the simulated hydrogen pressures by Methods 1, 2, and 3 with the experimental data for three CHSTs. In short, Method 2 can simulate the hydrogen temperature and pressure well during the charge–discharge process. Method 3 can simulate the approximate hydrogen temperature and precise hydrogen pressure during the charge–discharge process. Method 1 can only simulate the hydrogen pressure during the discharging process. The conclusions of this article can inform researchers which analysis methods are more reasonable to choose in future hydrogen‐filling studies.

Heat Transfer Analysis Methodology for Compression Hydrogen Storage Tank during Charge–Discharge Cycle

Temperature Effects of Composite High Pressure Hydrogen Storage Cylinders in the Rapid Hydrogen Charging and Discharging Process

Prediction of Dormancy Time of Cryo-Compressed Hydrogen Tank by Considering Dynamic Thermal Boundary

Numerical Analysis of Temperature Rise Within 70 MPa Composite Hydrogen Vehicle Cylinder During Fast Refueling

A numerical study on the thermal behavior of high pressure hydrogen in the on-board storage cylinder

Thermodynamic and heat transfer models for refueling hydrogen vehicles: Formulation, validation and application

Thermo-mechanical Investigation of Composite High-Pressure Hydrogen Storage Cylinder During Fast Filling

Theoretical investigation on heat leakage distribution between vapor and liquid in liquid hydrogen tanks

Modeling and thermodynamic analysis of thermal performance in self-pressurized liquid hydrogen tanks

Thermodynamic Analysis of the Effect of Initial Ortho-Hydrogen Concentration on Thermal Behaviors for Liquid Hydrogen Tanks

Thermal Models for Self-Pressurization Prediction of Liquid Hydrogen Tanks: Formulation, Validation, Assessment, and Prospects

Thermodynamic modeling and analysis of cascade hydrogen refuelling with three-stage pressure and temperature for heavy-duty fuel cell vehicles

Numerical Modeling for Rapid Charging of Hydrogen Gas Vessel in Fuel Cell Vehicle

Parametric study of hydrogen filling process in type IV tank based on CFD simulation

Thermodynamic modeling and analysis of hydrogen storage systems in hydrogen refueling stations

Dynamic Thermal Performance of Cryogenic Liquid Hydrogen Heating from Gas-Liquid Stratification to Supercritical under a Constant Heat Flux Condition: A Two-Step Simulation

Numerical Investigation of the Initial Charging Process of the Liquid Hydrogen Tank for Vehicles

Heat Transfer Analysis of High-Pressure Hydrogen Storage Tanks Subjected to Localized Fire

Lumped Parameter Modeling of SAE J2601 Hydrogen Fueling Tests

Modeling Heat and Mass Transfer in Metal Hydride-Based Hydrogen Storage Systems Using the Finite Volume Method

Towards fast and safe hydrogen filling for the fuel vehicle: A variable mass flow filling strategy based on a real-time thermodynamic model