Abstract:Obtaining a perovskite light-absorbing layer with good crystallization, low defect concentration, good stability, and well-matched energy levels is critical to obtaining high-efficiency perovskite solar cells (PSCs). Here, a hybrid PSC with a graded band gap is explored using MAPbBr3 (MA = CH3NH3) and MAPbBr0.9I2.1 quantum dots (QDs) as component cells. We have creatively designed a solar cell device with a double-QD structure [indium tin oxide (ITO)/SnO2/perovskite:MAPbBr3 QDs/MAPbBr0.9I2.1 QDs/Spiro-OMeTAD/Au]. A better crystal film of the perovskite absorption layer can be obtained because the MAPbBr3 QDs are doped in an antisolvent, which induces nucleation and growth in the polycrystalline perovskite. In addition, we expect that digestive ripening occurred in the crystallization, and the oleic acid ligands on the surface of the QDs disintegrate during the doping process and transfer to the surface of the perovskite absorption layer finally; it follows that the hydrophobicity and stability of the perovskite film are greatly enhanced. Moreover, a thin film of MAPbBr0.9I2.1 QDs is introduced between the perovskite absorption layer and the hole layer, acting as an energy-level ladder, which leads to well-matched energy levels, an increase in fill factor (FF), and an enhanced hole transport capability. In particular, the mechanism of the crystallization process involving the effect of oleic acid ligands on the interior and surface of the perovskite film is fully discussed here. The final research results from the PSCs show that both high efficiency and long-term stability are achieved successfully by this design strategy.The Supporting Information is available free of charge at <a class="ext-link" href="/doi/10.1021/acsami.0c14191?goto=supporting-info">https://pubs.acs.org/doi/10.1021/acsami.0c14191</a>.Parameters of carrier lifetimes in TRPL, parameters and calculated values in the Owens two-liquid method experiment, and J–V parameters; QD dispersion images; AFM images; perovskite film images; contact-angle test images; EIS spectrum; and boxplot of J–V parameters (<a class="ext-link" href="/doi/suppl/10.1021/acsami.0c14191/suppl_file/am0c14191_si_001.pdf">PDF</a>)This article has not yet been cited by other publications.

High‐Performance Perovskite Solar Cell via Chirality‐Engineered Graphene Quantum Dot Interface Passivation

Enhanced Crystallization and Optimized Morphology of Perovskite through Doping Indium-Based Metal-Organic Assembly: Achieving Significant Solar Cell Efficiency Enhancements

Defect Passivation and Electrical Conductivity Enhancement in Perovskite Solar Cells Using Functionalized Graphene Quantum Dots

Boosting Multiple Interfaces by Co-Doped Graphene Quantum Dots for High Efficiency and Durability Perovskite Solar Cells.

Graphite-N Doped Graphene Quantum Dots as Semiconductor Additive in Perovskite Solar Cells

Synergistic passivation and energy level alignment by graphene quantum dots for high performance inverted CsPbI3 perovskite solar cells

A Small‐Molecule “charge Driver” Enables Perovskite Quantum Dot Solar Cells with Efficiency Approaching 13%

CH 3 NH 3 PbBr 3– x I x Quantum Dots Enhance Bulk Crystallization and Interface Charge Transfer for Efficient and Stable Perovskite Solar Cells

MoS2 Quantum Dot/Graphene Hybrids for Advanced Interface Engineering of CH3NH3PbI3 Perovskite Solar Cell with Efficiency over 20%

Synergistic Passivation and Down‐Conversion by Imidazole‐Modified Graphene Quantum Dots for High Performance and UV‐Resistant Perovskite Solar Cells

Tunable Photoluminescent Nitrogen-Doped Graphene Quantum Dots at the Interface for High-Efficiency Perovskite Solar Cells

Tailored Graphene Quantum Dots to Passivate Defects and Accelerate Charge Extraction for All-Inorganic CsPbIBr2 Perovskite Solar Cells

Efficient and highly light stable planar perovskite solar cells with graphene quantum dots doped PCBM electron transport layer

Hybrid PbS Quantum-Dot-in-Perovskite for High-Efficiency Perovskite Solar Cell.

Chiral-structured heterointerfaces enable durable perovskite solar cells

Two dimensional graphitic carbon nitride quantum dots modified perovskite solar cells and photodetectors with high performances

Enhancing the Efficiency of Perovskite Solar Cells through Interface Engineering with MoS2 Quantum Dots

High‐Efficiency and Stable Perovskite Solar Cells via Buried Interface Modification with Multi‐Functional Phosphorylcholine Chloride

Dual interfacial modification to improve the performance of CsPbBr3 perovskite solar cells

Over 15% Efficiency PbS Quantum‐Dot Solar Cells by Synergistic Effects of Three Interface Engineering: Reducing Nonradiative Recombination and Balancing Charge Carrier Extraction

Interfacial Bridging Enables High Performance Perovskite Solar Cells with Fill Factor over 85%