Abstract:The traditional fossil energy is becoming increasingly scarce and is a main cause of environmental pollution. Therefore, power generation by fossil fuels will face great challenges in future. Hydraulic power generation has the advantages of being relatively clean, renewable and widely available. However, this way mainly uses electromagnetic generators that are heavy. bulky, and become inefficient with low water supply. In addition, it is not suitable for harvesting energy from water in the form of raindrops which store huge clean energy. The droplet-based electricity generator (DEG) can convert the mechanical energy of droplets such as rain water into electrical energy. DEG has attracted increasing attention in recent years due to its wide application prospects in outdoor lighting, portable mobile electronic devices and automobile glass power generation. However, the DEG still has some critical problems. such as the upper limit of charge capacity and the upper limit of output voltage. which limit its application in practice. In this study. a DEG experimental system is developed firstly, which consists of a droplet generator, electricity generating structures, supporting structures and voltage measurement equipment. The electricity generating structure is the most important part of the whole system, which comprises a polytetrafluomethylene (PTFE) film on an indium tin oxide substrate (ITO) plus an aluminium electrode. The PTFE, a promising electret material with high charge storage capability and stability could serve as an ideal reservoir for charge storage, while electrostatically inducing opposite charge of the same amount on the ITO for possible charge transfer to an aluminium electrode. A falling water droplet spreads on the PTFE surface, which bridges the originally disconnected components (the PTFE/ITO and aluminium electrode) into a closed-loop electrical system. Then, a new charging mode for DEG has been discovered through extensive experiments. That is, a reciprocating friction experimental machine is used to reciprocate friction to the surface of the PTFE film to pre-charge it using different tools. Then the water drops one by one and impinges on the PTFE film. The PTFE film has been stored with charges as a result of prior reciprocating frictions between solid and solid. and as a result of contact electrification between liquid and solid after continuous droplet impinging. The charge capacity and output voltage of DEG can be increased by about 2.3 times after using this new charging mode compared with the simple droplet impingement charging. This high voltage output makes the DEG possible to match the higher voltage electricity environment. Thirdly, through comparative analysis. the additional reciprocating frictions should be moderate and segmented. The excessive or adding reciprocating frictions at a time will reduce the charging efficiency. This paper also analyzes the relationship between droplet spreading state and output voltage through high-speed camera and oscilloscope. The linear relationship between the negative voltage peak and the positive voltage peak in the power generation process has been observed. The effects of friction tool, falling height and impinging frequency on the DEG have been investigated. It is found that using the friction tool of napkins with larger roughness can generate higher voltage. The impinging frequency of 2 Hz can generate the highest voltage compared with lower and larger impinging frequencies. In the falling height range from 5 to 15 cm,15 cm height can produce the highest voltage. Lastly, stopping droplets impinging on PTFE film will cause a decrease in the output voltage of DEG. If the stopping time is too long, the upper limit of the charge capacity of the power generation film will decrease. These findings provide new ideas and methods for improving DEGs' power generation capacity.

Quick evaluation and regulation of the maximum instantaneous power and matching resistance for droplet-based electricity generators

Droplet-enabled controllable manipulation of tribo-charges from liquid-solid interface

Performance and power management of droplets-based electricity generators

Hydrodynamic Constraints on the Energy Efficiency of Droplet Electricity Generators

A droplet‐based electricity generator incorporating Kelvin water dropper with ultrahigh instantaneous power density

Development of Multi Droplet-based Electricity Generator System for Energy Harvesting Improvement from a Single Droplet

Effect of water droplet wetting behavior on water-droplet-based electricity generator performance

A Single‐Droplet Electricity Generator Achieves an Ultrahigh Output Over 100 V Without Pre‐Charging

Field Enhanced Robust Droplet Electricity Generation

A droplet-based electricity generator for large-scale raindrop energy harvesting

Research on high instantaneous power droplet generator by using super-hydrophobic electrode

A droplet-based electricity generator with high instantaneous power density, high efficiency and reliable long-term stability

Boosted energy harvesting in droplet electrochemical cell with non-equilibrium electrical double layer

Relationship between water droplet motion and output characteristics in droplet-based electricity generator

Mathematic and Numerical Analysis of Droplet-based Electricity Generator

New charging mode of a droplet generator and its influencing factors

Droplet-Based Direct-Current Electricity Generation Induced by Dynamic Electric Double Layers

Droplet‐Based Electricity Generator toward Practicality: Configuration, Optimization, and Hybrid Integration

Enhancing Water Droplet-Based Electricity Generator by Harnessing Multiple-Dielectric Layers Structure

Bimodal Droplet‐Based Electricity Generation Through Semi Cassini Oval Dynamic Morphology Control

Monolithic Integrated Flexible Yet Robust Droplet‐Based Electricity Generator