Abstract:Obtaining a perovskite light-absorbing layer with good crystallization, low defect concentration, good stability, and well-matched energy levels is critical to obtaining high-efficiency perovskite solar cells (PSCs). Here, a hybrid PSC with a graded band gap is explored using MAPbBr3 (MA = CH3NH3) and MAPbBr0.9I2.1 quantum dots (QDs) as component cells. We have creatively designed a solar cell device with a double-QD structure [indium tin oxide (ITO)/SnO2/perovskite:MAPbBr3 QDs/MAPbBr0.9I2.1 QDs/Spiro-OMeTAD/Au]. A better crystal film of the perovskite absorption layer can be obtained because the MAPbBr3 QDs are doped in an antisolvent, which induces nucleation and growth in the polycrystalline perovskite. In addition, we expect that digestive ripening occurred in the crystallization, and the oleic acid ligands on the surface of the QDs disintegrate during the doping process and transfer to the surface of the perovskite absorption layer finally; it follows that the hydrophobicity and stability of the perovskite film are greatly enhanced. Moreover, a thin film of MAPbBr0.9I2.1 QDs is introduced between the perovskite absorption layer and the hole layer, acting as an energy-level ladder, which leads to well-matched energy levels, an increase in fill factor (FF), and an enhanced hole transport capability. In particular, the mechanism of the crystallization process involving the effect of oleic acid ligands on the interior and surface of the perovskite film is fully discussed here. The final research results from the PSCs show that both high efficiency and long-term stability are achieved successfully by this design strategy.The Supporting Information is available free of charge at <a class="ext-link" href="/doi/10.1021/acsami.0c14191?goto=supporting-info">https://pubs.acs.org/doi/10.1021/acsami.0c14191</a>.Parameters of carrier lifetimes in TRPL, parameters and calculated values in the Owens two-liquid method experiment, and J–V parameters; QD dispersion images; AFM images; perovskite film images; contact-angle test images; EIS spectrum; and boxplot of J–V parameters (<a class="ext-link" href="/doi/suppl/10.1021/acsami.0c14191/suppl_file/am0c14191_si_001.pdf">PDF</a>)This article has not yet been cited by other publications.

Controlled solid‐state Phase Transition of Formamidinium Dominated Perovskite Layers Fabricated Through Magnetron Sputtering for Photovoltaics

Organic‐Inorganic Perovskite Films and Efficient Planar Heterojunction Solar Cells by Magnetron Sputtering

Bridging‐Solvent Strategy for Quasi‐Single‐Crystal Perovskite Films and Stable Solar Cells

Heterogeneous Nucleation and Enhanced Charge Transfer via Amorphous Metal‐Organic Frameworks for Efficient and Stable Perovskite Solar Cells

Controlling Intermediate Phase Formation to Enhance Photovoltaic Performance of Inverted FA-Based Perovskite Solar Cells

Multifunctional anion-cation modulation engineering for Sn-Pb perovskite solar cells

Controlled Nucleation and Oriented Crystallization of Methylammonium‐Free Perovskites via In‐Situ Generated 2D Perovskite Phases

Zwitterion-Stabilizing Scalable Bladed -Phase Cs<sub>0.1</sub>FA<sub>0.9</sub>PbI<sub>3</sub> Films for Efficient Inverted Planar Perovskite Solar Cells

Engineering the intermedi-ate adduct phase to con-trol the crys-tallization of perovskites for efficient and stable perov-skite solar cells

Protic Amine Carboxylic Acid Ionic Liquids Additives Regulate α‐FAPbI 3 Phase Transition for High Efficiency Perovskite Solar Cells

2,2‐Azodi(2‐Methylbutyronitrile)‐coordinated Intermediate Phase Engineering for Efficient and Stable Perovskite Solar Cells

Combined Precursor Engineering and Grain Anchoring Leading to MA‐free, Phase‐pure and Stable Α‐formamidinium Lead Iodide Perovskites for Efficient Solar Cells

CH 3 NH 3 PbBr 3– x I x Quantum Dots Enhance Bulk Crystallization and Interface Charge Transfer for Efficient and Stable Perovskite Solar Cells

Impacts of MAPbBr3 Additive on Crystallization Kinetics of FAPbI3 Perovskite for High Performance Solar Cells

MACl-Induced Controlled Crystallization in Sequentially Deposited Perovskites for High-Efficiency and Stable Perovskite Solar Cells

Cetrimonium bromide and potassium thiocyanate assisted post-vapor treatment approach to enhance power conversion efficiency and stability of FAPbI3 perovskite solar cells

Stable α‐FAPbI3 via porous PbI2 for efficient perovskite solar cells

Mixed-Organic-Cation (FA)x(MA)1-xPbI3 Planar Perovskite Solar Cells with 16.48% Efficiency via a Low-Pressure Vapor-Assisted Solution Process

Regulated Film Quality With Methylammonium Bromide Addition In A Two-Step Sequential Deposition To Improve The Performance Of Perovskite Solar Cells

Constructing Graded Perovskite Homojunctions by Adding Large Radius Phenylmethylamine Ions for Sequential Spin-Coating Deposition Method To Improve the Efficiency of Perovskite Solar Cells

Ultra-smooth CsPbI2Br Film Via Programmable Crystallization Process for High-Efficiency Inorganic Perovskite Solar Cells