Abstract:Dielectric barrier discharge (DBD) plasma recently has been demonstrated as an effective in situ heating methodology in anti-ice and de-ice applications of the aircraft. However, the thermal stability of this special heat source during the interactions between the plasma and the ice block may pose serious concerns. In this paper, it is found that when the ice blocks of different characteristic locations covered the DBD device with alternative current (AC) power, two different kinds of interaction processes can be resulted: First, the concentration of the heat flow through the local enhancement of the streamers between the electrode and the ice, long-lasting for the glaze ice ended with the partial evaporation of the melted ice block with larger separations, or short-lived intermittent for the rime ice until the boundary is beyond the reach. Second, sparks, very likely to be generated between the electrode and the ice block when the separation and electric field meet the transition conditions, resulting in the fast evaporation of the melted ice block and the severe aging or on-sight burning of the devices, even at the operation voltage safe for the AC-DBD plasma without ice blocks. It is emphasized that the coexistence or the number of the ice blocks of different separations does not alter such behavior. Supported by the calculation of the streamer-to-spark transition criterion, and affected by ice phase change, it is argued that the de-icing ACDBD plasma is a strong nonlinear heat source, resulting from the surface charge accumulation, melting of the ice blocks, and the enhancement of ionization collision frequency due to the mixing of the evaporated water molecules. A new critical condition, the critical surface charge density was proposed for the initiation of spark, rho(sc): Densities higher than rho(sc) will lead to the catastrophic spark, while the lower will lead to the selective concentration of the heat flow for the faster de-icing process. Due to the random distribution nature of the electrode-to-ice separations during the real-world practice of an AC-DBD heat source for de-icing, the existence of rho sc may be under further scrutiny and considered as a crucial factor for the stable operation of the plasma heat sources for de-icing. (c) 2022 Elsevier Ltd. All rights reserved.

Comparative Experimental Study on the De-Icing Performance of Multiple Actuators

Induction Heating Characteristics of Electroless Ni-Coated CFRP for Deicing and Anti-Icing

Performance and mechanism analysis of nanosecond pulsed surface dielectric barrier discharge based plasma deicer

Experimental Study on Anti-Icing Performance of NS-DBD Plasma Actuator

Experimental Investigation of Deicing Characteristics Using Hot Air As Heat Source

Evolution of a single sessile droplet under the influence of the dielectric barrier discharge plasma actuator

Experiment Investigation on Deicing Characteristics and Energy Efficiency Using Infrared Ray As Heat Source

Comparative Study of Using Superhydrophobic and Icephobic Surface Coatings for Aircraft Icing Mitigation

Experimental Study on the Effects of Substrate Hydro-/Icephobicity on Ice Mitigation and Ice Shedding During the Dynamic Icing Process over the Rotating Propeller of an Unmanned-Aerial-Vehicle

SDBD Based Plasma Anti-Icing: A Stream-Wise Plasma Heat Knife Configuration and Criteria Energy Analysis

Geometrical and electrical optimization of NS-SDBD streamwise plasma heat knife for aircraft anti-icing

Piezoelectric deicing system for aeronautics: Extensional mode actuator and power supply

Low-energy avionic piezoelectric deicing system

Plasma Characteristics and De-icing of Three-electrode Double-sided Pulsed Surface Dielectric Barrier Discharge

Thermal Characteristic and Spatial Morphology Between Electrode and Phase Changing Ice During De-Icing Process of Dielectric Barrier Discharge and Critical Behavior of the Surface Charge Density

Comparative study on the influence of surface characteristics on de-icing evaluation

Sandwich-structured intelligent anti-icing/de-icing film with ice-oriented power self-regulating performance

Flight Safety Oriented Ice Shape Modulation Using Distributed Plasma Actuator Units

Experimental Study on the Ice Freezing Adhesive Characteristics of Metal Surfaces

Investigation of airflow thermal ice melting process under various flight conditions

Integrated Composite Electrothermal De-Icing System Based on Ultra-Thin Flexible Heating Film