Abstract:Total knee arthroplasty (TKA) is a cornerstone in addressing knee joint disorders, significantly enhancing patients' quality of life. However, despite technological advancements, a comprehensive understanding of the dynamic stresses experienced by knee prostheses during daily activities, particularly under rehabilitation interventions, remains elusive. This study aims to bridge this gap by employing numerical simulations and finite element analysis to elucidate these dynamic stresses and their interaction with rehabilitation protocols. A real-life knee replacement prosthesis model was meticulously constructed through coordinate measuring and 3D scanning, facilitating detailed finite element analysis in ANSYS Workbench version 17.1. Two distinct boundary conditions and loading scenarios were applied, with comparisons made between linear and nonlinear material assumptions. The simulation results using these different boundary condition methods revealed minimal differences. Specifically, at a knee angle of 0°, the relative stress error rate between the two boundary condition types was approximately 1 % (1.11 MPa and 1.099 MPa, respectively). At 15° and 90°, the error rates were 1.9 % and 0.56 %, respectively (10.275 MPa and 10.078 MPa at 15°; 10.275 MPa and 10.078 MPa at 90°). Given these minimal differences, the first type of boundary condition was adopted for the subsequent scenarios to enhance convergence efficiency in the analysis. Moreover, comparative analyses between linear and nonlinear material behaviors demonstrated acceptable agreement, offering insights into potential efficiency gains in simulation methodologies. Building on this foundation, an optimized tibial model was proposed, incorporating geometric alterations to the tray. Quantitative assessments revealed significant reductions, with von Mises stress decreasing by 23.35 % and equivalent strain by 17 % at a knee angle of 140°. Further evaluations at varying angles, including 60°, consistently showed positive influences on stress and strain. These quantitative findings not only contribute valuable insights into the mechanical behavior of knee prostheses but also provide tangible evidence for the efficacy of linear material behavior assumptions. The proposed optimized model exhibits promising potential for enhancing the design and performance of knee prostheses, particularly under critical loading conditions. In conclusion, these results underscore the importance of a nuanced understanding of knee prosthesis behavior during rehabilitation, offering a quantitative foundation for refining existing designs and informing the development of next-generation prostheses.

Analysis of knee-bending motion through three-dimensional scanning for advanced brace design

Biomechanical Strengthening Design for Limb Articulation Based on Reconstructed Skeleton Kinesthetics

Design and Verification of a New 3D Printed Customized Unilateral Load-reduction Knee Brace

Cycling knee brace design analysis using 3D virtual clothing program to assess clothing pressure distribution and variance

Knee Biomechanics during Walking in Individuals with Anterior Cruciate Ligament Repair: The Role of a Custom 3D Printed Knee Brace

Design and evaluation of a wedge-shaped adaptive knee orthosis for the human lower limbs

Design And Fabricate A Brace Joint With A New Intermittent Correction Varum Mechanism for Patients With Medial Compartment Knee Osteoarthritis and to Investigate Its Effect on A Patient's Gait Parameters (Case Report)

The effect of knee braces on knee joint kinematics at different exercise speeds

Finite-element simulation of functional knee sleeves based on three-dimensional modeling of the knee joint

Use of Anthropometric Data from the Medial Tibial and Femoral Condyles to Design Unicondylar Knee Prostheses in the Chinese Population

Efficiency and comfort of knee braces: A parametric study based on computational modelling

Ankle sprain bracing solutions and future design consideration for civilian and military use

The 3D Analysis of the Sagittal Curvature of the Femoral Trochlea in the Chinese Population

Study on three-dimensional kinematics and electromyography of ACL deficient knee participants wearing a functional knee brace during running

Design and Implementation of a Wearable System Based on a Flexible Capacitive Sensor, Monitoring Knee Laxity

Finite Element Analysis and Mechanical Assessment for the Constraint of Total Knee Replacement

The effect of different mechanism combinations on sliding between brace and lower limb during walking and leg-raising

Design of a personalized knee rehabilitation exoskeleton with high motion compliance

Effect of Brace Design on Patients with ACL-Ruptures

The Patient-Specific Brace Design and Biomechanical Analysis of Adolescent Idiopathic Scoliosis

Numerical investigation of knee prosthesis stresses in daily activities: Insight into knee rehabilitation and Creation of a new optimal model