Abstract:In some traditional formative and additive manufacturing processes widely used in the fabrication of steel products, stress conditions and metallurgy typically result in a strong texture and mechanical anisotropy in both rolling high-strength low-alloy steel and additive manufacturing stainless steel products. To resolve this problem, we have investigated the effectiveness of a novel wire-arc additive manufacturing method in which the heat source is substituted by high-efficiency submerged arc plasma i.e., submerged arc additive manufacturing. An isotropic microstructure can be obtained in the bulk of large-scale low-carbon steel components by ensuring a complete columnar-to-equiaxed transition. We found that the top zone of the as-deposited component comprised columnar α-Fe grains with a typical preferential <001>α orientation. Multiple allotropic transformations were triggered by an in-situ intrinsic heat treatment (mainly the combination of multi-layer-penetration normalizing, full-layer-penetration inter-critical annealing, and long-duration tempering—i.e., NIT). Consequently, when the net bead height was no greater than the width of the fine grain zone affected by the previous layer of deposition, the microstructures in each new layer could be progressively refined and homogenized. Therefore, the intermediate zone was predominantly composed of fully equiaxed α-Fe and displayed homogeneous characteristics along the build direction. During full-layer NIT treatment, the pearlite was spheroidized slightly, reduced both in size (from 4μm to 2μm) and in area fraction (from ~5% to ~1%), thereby mitigating cracking susceptibility. Moreover, not only were the intracrystalline dislocations significantly reduced, but also their morphology evolved from tangled to movable lines. These changes, along with finer grains and the formation of high-angle grain boundaries, led to lower and more dispersed internal strain in the α-Fe matrix. Consequently, excellent Charpy toughness (over 300 J at -60 °C) with minimal deterioration in strength was achieved. Impact, tensile, and hardness tests revealed nearly isotropic mechanical characteristics. We believe that this novel method shows tremendous promise in large-scale additive manufacturing.

Ultrasonic impact-fused arc additive manufacturing technology in the heat treatment of ultra-high strength steel manufacturing

Effect of Induction Heat Treatment on Microstructure, Mechanical and Corrosion Properties of Stainless Steel 308L Fabricated Using Wire Arc Additive Manufacturing

Submerged arc additive manufacturing (SAAM) of low-carbon steel: Effect of in-situ intrinsic heat treatment (IHT) on microstructure and mechanical properties

Effect and mechanism of inter-layer ultrasonic impact strengthening on the anisotropy of low carbon steel components fabricated by wire and arc additive manufacturing

The influence of different ultrasonic impact treatment modes on microstructure and mechanical properties of 18Ni-300 steel fabricated by wire arc additive manufacturing

Study on arc-ultrasonic welding technology

The effects of ultrasonic frequency pulsed arc on wire + arc additively manufactured high strength aluminum alloys

Investigation of 300M ultra-high-strength steel deposited by wire-based gas metal arc additive manufacturing

Effect of Ultrasonic Treatment on Microstructure and Properties of 2000 MPa Ultra-High-Strength Steel-Welded Joints

Effect of Induction Heat Treatment on Residual Stress Distribution of Components Fabricated by Wire Arc Additive Manufacturing

Numerical study of the ultrasonic impact on additive manufactured parts

Effect of heat treatment temperature on microstructure and tensile properties of austenitic stainless 316L using wire and arc additive manufacturing

Effect of induction heat treatment on microstructure, mechanical and corrosion properties of stainless steel 308 L fabricated using wire arc additive manufacturing

Effect of ultrasonic shot peening on microstructure and mechanical properties of GH3230 superalloy during selective laser melt solution heat treatment

Heat Treatment Optimization of 2219 Aluminum Alloy Fabricated by Wire-Arc Additive Manufacturing

Effect of heat treatment on microstructure and mechanical properties of WE43 alloy fabricated by wire arc additive manufacturing

Improving mechanical properties of austenitic stainless steel by the grain refinement in wire and arc additive manufacturing assisted with ultrasonic impact treatment

Wire and Arc Additive Manufacturing of High‐Strength Low‐Alloy Steel: Microstructure and Mechanical Properties

Frictional Wear and Thermal Fatigue Properties of Die Steel after Ultrasound-Assisted Alloying

Effect of Interlayer Temperature on Microstructure and Properties of High-Strength Low-Alloy Steel Manufactured Using Submerged-Arc Additive Manufacturing (SAAM)

Effects of Arc-Excited Ultrasonic on Microstructures and Properties of Weld