Abstract:Introduction. Functionally graded materials are of great use, because heterogeneity of properties enables to control the strength and rigidity of structures. This has caused great interest in the topic in the world scientific literature. The construction of solutions to such problems depends significantly on the type of boundary conditions. In this paper, we consider the equilibrium of a thin-walled circular cylinder whose mechanical properties change along the radius. Homogeneous boundary conditions were set on cylindrical surfaces that had not been considered before, the effect was on the ends. The mathematical formulation of the problem was carried out in the linear theory of elasticity in the framework of axisymmetric deformation. Expressions were constructed for the components of the stress-strain state of the cylinder, in which some coefficients were found from the solution to the resulting system of linear algebraic equations. Materials and Methods. The material of the cylinder was linearly elastic, the elastic modulus of which depended linearly on the radial coordinate. The basic research method was the asymptotic method, in which half the logarithm of the ratio of the outer and inner radii acted as a small parameter. Iterative processes were used to construct the characteristics of the stress-strain state of the cylinder. Results. Homogeneous solutions to the boundary value problem were obtained for a linearly elastic functionally gradient hollow thin-walled cylinder. An analysis of these solutions made it possible to reveal the nature of the stress-strain state in the cylinder wall. For this purpose, an asymptotic analysis of the solutions was carried out, relations for displacements and stresses were obtained. It was determined that those solutions corresponded to the boundary layer, while their first terms determined Saint-Venant edge effect similar to the plate theory. Discussion and Conclusion. The analytical solution to the equilibrium problem of a thin-walled cylinder inhomogeneous in radius constructed by asymptotic expansion can be used for numerical solution to a specific problem. For this, it is required to solve the obtained systems of linear algebraic equations and determine the corresponding coefficients. The resulting asymptotic representations provide analyzing the three-dimensional stress-strain state. The selection of the number of expansion terms makes it possible to calculate displacements and stresses with a given degree of accuracy. This analysis can be useful in assessing the adequacy of applied calculation methods used in engineering practice.

Analysis of elastic stresses in rotating cylinders made of Titanium and Bronze materials

Elastic-plastic Stress Distribution of Rotating Annular Disc Based on Twin-Shear Stress Yield Criterion

A Study of the Back Stress and the Friction Stress Behaviors of Ti-6Al-4V Alloy During Low Cycle Fatigue at Room Temperature

A parametric study on the elastic limit stresses of rotating variable thickness orthotropic disk

Stress field analysis of functionally graded polar orthotropic disk on a rigid inclusion subjected to variable angular velocity

STRESS ANALYSIS ON FUNCTIONALLY GRADED MATERIAL CYLINDER UNDER THERMAL-MECHANICAL LOAD

Thermoelastic Stresses Alleviation for Two-Dimensional Functionally Graded Cylinders under Asymmetric Loading

A novel approach to stress analysis of pressurized FGM cylinders, disks and spheres

Finite Element Simulation of Micro Stresses and Micro Strains in Two-Phase Titanium Alloy during Tension

Effect of Convection, Internal Heat Source, and Solar Radiation on the Stress Analysis of a Rotating Functionally Graded Smart Disk

INFLUENCE OF VARIABLE YOUNG’S MODULUS ON RESIDUAL STRESSES INDUCED BY ROTATIONAL AUTOFRETTAGE OF A TUBE WITH FIXED ENDS

Hot Deformation and Constitutive Modeling of TC21 Titanium Alloy

Stress analysis of functionally graded hyperelastic variable thickness rotating annular thin disk: A semi-analytic approach

Experimental characterization of anisotropic tensile mechanical behavior of pure titanium tube

Study of Microstructure and Mechanical Properties by Torsional Behavior in Axial Closed Die Rolling Forming

Experimental analysis of the multiaxial failure stress locus of commercially pure titanium at low and high rates of strain

Analysis of Stress-Strain State of a Cylinder with Variable Elasticity Moduli Based on Three-Dimensional Equations of Elasticity Theory

Study on the Corrosion Behavior and Numerical Simulation of TC18 Titanium Alloy under Tensile Stress

Arrhenius-Type Constitutive Equation Model of Superplastic Deformation Behaviour of Different Titanium Based Alloys

Analysis and modelling of a rotary forming process for cast aluminum alloy A356

A thermomechanical model for the analysis of disc brake using the finite element method in frictional contact