Abstract:The sustainability metrics of both crystalline Silicon and CdTe PV technologies have been drastically improved during the last 7 years. This paper quantifies improvements resulting from better material and energy utilization and higher module efficiencies coupled with lower degradation losses and potentially longer life expectancies. Current production CdTe modules (series 6 and series 7) are analyzed in terms of their energy performance and environmental footprint and compared with the older series 4 module production and current single‐crystalline Silicon (sc‐Si) module production. This paper provides a comprehensive assessment of the up‐to‐date life‐cycle sustainability status of cadmium‐telluride based photovoltaic (PV) systems. Current production modules (Series 6 and Series 7) are analyzed in terms of their energy performance and environmental footprint and compared with the older series 4 module production and current single‐crystalline Silicon (sc‐Si) module production. For fixed‐tilt systems with Series 6 modules operating under average US irradiation of 1800 kWh/m2/year, the global warming potential (GWP) is reduced from 16 g CO2eq/kWh in Series 4 systems to 10 CO2eq/kWh in Series 6 systems. For operation in US‐SW irradiation of 2300 kWh/m2/year, the GWP is reduced from 11 to 8 CO2eq/kWh and for 1‐axis tracking systems operating in Phoenix, Arizona, with point‐of array irradiation of 3051 kWh/m2/year the GWP is reduced to 6.5 CO2eq/kWh. Similar reductions have happened in all environmental indicators. Energy payback times (EPBT) of currently installed systems range from 0.6 years for fixed‐tilt ground‐mounted installations at average US irradiation at latitude tilt installations to 0.3 years for one‐axis trackers at high US‐SW irradiation, considering average fossil‐fuel dominated electricity grids with fuel to electricity conversion efficiency of 0.3. The resulting energy return on energy investment (EROI) also depends on the conversion efficiency of the electricity grid and on the operation life expectance. For a 30‐year operational life and grid conversion efficiency of 0.3, EROI ranges from 50 (at US average irradiation) to 70 for US‐SW irradiation. The EROI declines with increased grid conversion efficiency; for CdTe PV operating in south California with grid conversion efficiency of 49%, the EROI is about 50 and is projected to fall to 30 when the state's 2030 target of 80% renewable energy penetration materializes. Material alternatives that show a potential of further reductions in degradation rates and materials for enhanced encapsulation that would enable longer operation lives have also been investigated. A degradation rate of 0.3%/year, which has been verified by accelerated testing, is assumed in 30‐year scenarios; this is projected to be reduced to 0.2%/year in the near‐term and potentially to 0.1%/year in the longer term. With such low degradation rates and enhanced edge‐sealing, modules can last 40‐ to 50‐years. Consequently, all impact indicators will be proportionally reduced while EROI will increase. This detailed LCA was conducted according to ISO standards and IEA PVPS Task 12 guidelines. The study revealed that the choices of system models, methods and temporal system boundaries can significantly impact the results and points out to the need to include assumptions regarding these choices in the "transparency in reporting" requirements listed in the IEA PVPS Task 12 Guidelines.

Global warming potential of photovoltaics with state-of-the art silicon solar cells: Influence of electricity mix, installation location and lifetime

Environmental Assessment of Solar Cell Materials

Photovoltaic panel waste assessment and embodied material flows in China, 2000-2050

Material intensity and carbon footprint of crystalline silicon module assembly over time

Life Cycle Assessment of Grid-Connected Photovoltaic Power Generation from Crystalline Silicon Solar Modules in China

Analogical environmental cost assessment of silicon flows used in solar panels by the US and China

Assessing the Environmental Benefits of Extending the Service Lifetime of Solar Photovoltaic Modules

Performances of typical photovoltaic module production from the perspective of life cycle sustainability assessment

State and prospects of photovoltaic module waste generation in China, USA, and selected countries in Europe and South America

Circular economy priorities for photovoltaics in the energy transition

Design for the environment: SHJ module with ultra‐low carbon footprint

Effect of Recycling on the Environmental Impact of a High-Efficiency Photovoltaic Module Combining Space-Grade Solar Cells and Optical Micro-Tracking

Global perspectives on advancing photovoltaic system performance—A state-of-the-art review

Dynamic material flow analysis of silicon photovoltaic modules to support a circular economy transition

Updated sustainability status of cadmium telluride thin‐film photovoltaic systems and projections

Towards market commercialization: Lifecycle economic and environmental evaluation of scalable perovskite solar cells

An Overview on Recycling of Photovoltaic Modules at the End of Life (EoL)

Upgraded Metallurgical Grade Silicon for solar electricity production: a comparative Life Cycle Assessment

Role of solar PV in net‐zero growth: An analysis of international manufacturers and policies

The EU Ecodesign Directive ‐ Analysis of Carbon Footprint Assessment Methodology and Implications for PV Module Manufactures

On Climate Change and Photovoltaic Energy Production