Abstract:The paper is focused on testing the weld of the S960MC steel produced at the micro-jet cooling under static and fatigue loading at critical parameters. This kind of material was in the form of a sheet with a thickness equal to 2 mm. The joint was obtained using three different types of welding wires: EDFK 1000, Union NiMoCr and Union X96 at the same parameters of the process. The joints were examined using non-destructive and destructive tests. The results from non-destructive experiments enable us to assess the quality of the welds directly before the joining process. In contrast, the destructive one allows following welds behavior under different loading conditions with their critical parameters. The bending experiments confirmed the good plastic properties of the weld, expressed by no cracks in the region tested in many variants of the joint manufactured. The results from static tests indicated a significant reduction of mechanical parameters of the weld in comparison to the base metal, expressed by 50% differences. Fatigue data have enabled us to follow the welding behavior at the increasing amplitude of axial stress up to fracture at constant amplitude value covering the following values of stress 650 MPa–100 MPa. Variations of total energy are presented at different values of several cycles up to fracture. Fracture regions are collected for analysis of the joint region features under cyclic loading. They have indicated differences in weld cracking depended on the stress level. Finally, the Wöhler S-N curve of the weld was determined, indicating the value of the fatigue limit of the weld tested, i.e., 100 MPa. The weld at the Union NiMoCr welding wire was indicated as the joint having the highest resistance on static and fatigue loadings.

Microstructural and Mechanical Characterizations of Weld Metal of S960QL Ultra High Strength Steel Joints Obtained with Different Multi-Pass Laying Techniques using GMAW

Investigations on Mechanical Strength and Microstructure of Multi-Pass Welded S690QL HSLA Steel Using MAG and FCAW

Undermatched Welding of Ultra-High-Strength Steel S1100 with Metal-Cored Wire: Influence of Welding Positions on Mechanical Properties

Mechanical properties and microstructural evaluation of the heat-affected zone in ultra-high strength steels

Welding of S1100 Ultra high‐Strength Steel Plates with Matching Metal‐Cored Filler Wire: Microstructure, Residual Stresses, and Mechanical Properties

Welding of S960QL High-Strength Steel by the Manual–Automated MAG Technique—A Study of Mechanical Properties, Residual Stresses and Fracture Mechanisms in the Heat-Affected Zone

Thermo mechanical and microstructural constituents of dissimilar S700MC-S960QC high-strength steel welded joints using overmatched filler wire

A Comparative Study on Microstructural Characterization of Thick High Strength Low Alloy Steel Weld by Arc Welding and Laser Welding

Insights into microstructure evolution and fracture mechanisms of welded joints of high strength steel patchwork components

Investigation of Microstructure and Mechanical Properties of High-Depth-to-Width-Ratio Horizontal NG-GMAW Joint for S500Q Steel

Microstructure and mechanical properties of dissimilar materials joints between T92 martensitic and S304H austenitic steels

Microstructure and Mechanical Properties of MIG Welds between 6252 Armor Steel and Q550D HSLA Steel

Behavior of Weld to S960MC High Strength Steel from Joining Process at Micro-Jet Cooling with Critical Parameters under Static and Fatigue Loading

Insight on microstructure and mechanical properties of 40 mm thick-walled ferromagnetic super-MSS by magnetic-field-assisted narrow gap GTAW

Microstructure and Mechanical Properties of Multi-Pass TIG Welded Joint of Thick Al–Zn–Mg Alloy Plate

Microstructure and mechanical properties of HSLA thick plates welded by novel double-sided gas metal arc welding

Microstructural Characteristics and Mechanical Properties in the Laser Beam Welded Joints of High-Strength Microalloyed Steel

Microstructures and Properties of 50 mm Thick SA508Gr.3Cl.2 Steel Welding Joints by Ultra-Narrow-Gap Laser Welding with Filler Wire

Microstructural characterization and mechanical properties of inertia friction welded FGH96 joints

Microstructure and softening of advanced high-strength steel QP1180 lap joints welded with CMT

Microstructure and Softening of Laser-Welded 960 MPa Grade High Strength Steel Joints