Surface Topography in Cutting-Speed-Direction Ultrasonic-Assisted Turning

Thanh-Trung Nguyen,Toan-Thang Vu,Thanh-Dong Nguyen

DOI: https://doi.org/10.3390/mi15060668

IF: 3.4

2024-05-22

Micromachines

Abstract:Ultrasonic vibration has been employed to assist in turning, introducing intermittent machining to reduce average cutting force, minimize tool wear, and enhance machining efficiency, thereby improving surface roughness. However, achieving intermittent cutting necessitates specific conditions, with a cutting speed or feed rate falling below the critical speed associated with the ultrasonic vibration parameters. This study presents a theoretical model for surface formation in cutting-speed-direction ultrasonic-assisted turning (CUAT), covering both continuous and intermittent machining regimes. Experimental validation was conducted on C45 carbon steel and 201 stainless steel to demonstrate the applicability of the theoretical model across different materials. Digital microscope analysis revealed 3D topography consistency with the theoretical formula. Surface roughness evaluations were performed for both CUAT and CT (conventional turning) methods. The results indicated a significant reduction in roughness Ra for C45 steel samples machined with CUAT, up to 80% compared to CT at a cutting speed of 20 m/min, while only exhibiting slight fluctuations when turning 201 stainless steel. Detailed analysis and explanation of these phenomena are presented herein.

nanoscience & nanotechnology,instruments & instrumentation,physics, applied,chemistry, analytical

What problem does this paper attempt to address?

The problem that this paper attempts to solve is how to understand the formation mechanism of surface topography through theoretical models and experimental verification in the process of ultrasonic - assisted cutting (CUAT), especially the influence of ultrasonic vibration on surface roughness when the cutting speed is lower than the critical value.

### Main research contents:
1. **Theoretical model**:
- The paper proposes a theoretical model to describe the formation of surface topography in the ultrasonic - assisted cutting (CUAT) process in the cutting - speed direction. This model covers both continuous cutting and intermittent cutting modes.
- The formula \( v_a = v_c + v_u = v_c + 2\pi A f \cos(2\pi f t + \phi) \) describes the synthetic cutting speed in ultrasonic - assisted cutting, where \( v_c \) is the traditional cutting speed, \( v_u \) is the ultrasonic vibration speed, \( A \) is the vibration amplitude, \( f \) is the vibration frequency, and \( \phi \) is the phase angle.
- When \( v_c \leq v_{\text{crucial}} = 2\pi A f \), intermittent cutting occurs; when \( v_c > v_{\text{crucial}} \), continuous cutting occurs.

2. **Experimental verification**:
- The experiment used a traditional lathe (OKK Ramo 1000) and carried out ultrasonic - assisted cutting on C45 carbon steel and 201 stainless steel at different cutting speeds.
- The surface topography was analyzed using a digital microscope (Keyence VHX 7000) to verify the accuracy of the theoretical model.
- The experimental results show that when the cutting speed is lower than the critical value, the surface roughness \( R_a \) of C45 carbon steel can be reduced by up to 80%, while the surface roughness of 201 stainless steel does not change much.

### Research significance:
- **Surface quality improvement**: Through ultrasonic - assisted cutting, especially at low cutting speeds, the surface roughness can be significantly improved and the surface quality of machined parts can be enhanced.
- **Mechanism explanation**: The paper explains in detail how ultrasonic vibration affects the formation of surface topography, especially the differences in intermittent cutting and continuous cutting modes.
- **Practical application**: This research provides theoretical basis and experimental data support for the practical application of ultrasonic - assisted cutting technology, which is helpful for optimizing the processing technology and improving production efficiency.

In conclusion, through theoretical modeling and experimental verification, this paper deeply explores the surface topography formation mechanism of ultrasonic - assisted cutting at different cutting speeds, especially the significant improvement effect on surface roughness.