Abstract:Objective: The control of biofilm and effluent contamination of dental unit water lines (DUWL) includes additions of antimicrobial solutions, as well as automatic dosing units. There are, however, varying reports on the effects of such agents on the bond strength of restorative dental materials and, particularly, between these agents and dental hard tissues. Methodology: The possible effects of an antimicrobial DUWL treatment solution on the adhesion of composite resin to dentin was evaluated by shear bond strength (SBS) testing. A total of 20 caries-free human molar and premolar teeth were used as the test substrates. The teeth were divided into two sets of 10 teeth which, after appropriate cleaning with water and pumice, were embedded horizontally in dental die stone. The buccal surface of each tooth was ground flat to a 17 microns finish using water-lubricated SiC paper. The teeth were then etched for 15 seconds with 37% H3PO4 and rinsed with either water (control) or a proprietary DUWL treatment (ICX) solution. Thereafter, the teeth were lightly blown dry with clean dry air, and the dentin conditioned with Prime & Bond NT for 20 seconds. The excess solvent was then removed by gentle air drying for 5 seconds, and the conditioner cured with visible light for 10 seconds. A cylinder of composite was placed on the conditioned surface and cured. A second group of 20 caries-free human molar and premolar teeth were used as test substrates to evaluate the effect of the ICX DUWL treatment solution on a different dentin priming system (OptiBond Solo Plus). The teeth in the second group were divided into two sets and after a 15 second etch with 37% H3PO4, were rinsed with water (control) or the proprietary ICX DUWL treatment solution. Thereafter, the teeth were lightly blown dry with clean, dry air and the dentin conditioned with OptiBond Solo for 20 seconds. The excess solvent was then removed by gentle air drying for 5 seconds, and the conditioner cured with visible light for 10 seconds. A cylinder of composite was placed on the conditioned surface and cured. Shear bond strength testing was performed with a universal test machine at the default cross-head speed of 0.1 mm/min. A set of teeth, sectioned, mounted and etched as above but rinsed with a 0.01% mineral oil/water mix prior to conditioning and bonding, was used as the negative control. A separate corrosion testing was performed by immersing brass coupons in water and ICX for 31 days and measuring the weight loss. The brass coupons were bright-dipped, electroless nickel-plated and bright nickel electroplated. Results: The bonding studies indicated that the DUWL treatment solution applied to a cut and etched dentin surface prior to conditioning and bonding with an adhesive system has no effect (p > 0.05) on bond strength for either group of specimens, compared to water. Negative control specimens were found to have minimal bond strengths. The corrosion study indicated no difference in the behavior of the test specimens in ICX compared to those in water, although differences were noted between the different surface finishes applied to the brass substrate. Conclusion: The findings of this study demonstrate that exposure of an etched dentin surface to a water-based DUWL treatment mixture has no adverse effects on subsequent adhesion strength. Minimal corrosive attack was noted in the ICX solution and water for brass coupons provided with three different surface finishes.

The effect of dentin surface treatment with disinfectant on the shear bonding strength of luting cements

[Effect of Different Treatments of Dentin Surface on Sheer Bond Strength Between Different Bonding Agents and Dentin].

Effect of Dentin Disinfection with 2% Chlorhexidine Gluconate and 0.3% Iodine on Dentin Bond Strength: An in vitro Study

Effect of disinfectant application methods on the bond strength of composite to dentin

Effect of Different Cavity Disinfectants on Adhesion to Dentin of Permanent Teeth

[Effect of Different Dentin Cleaning Agents on the Bond Strength of Self-Adhesive Resin Cement to Dentin].

Effect of a dental unit waterline treatment solution on composite-dentin shear bond strengths

The effect of prophylaxis method on microtensile bond strength of indirect restorations to dentin

Effect of Surface Treatments on Shear-bond Strength of Glass Ionomer Cements to Silver Diamine Fluoride-treated Simulated Carious Dentin

Effect of 2% chlorhexidine on resin bond strength and mode of failure using two different adhesives on dentin: An in vitro study

Effect of Medications for Root Canal Treatment on Bonding to Root Canal Dentin

Effect of Er, Cr: YSGG, Nd: YAG, and diode laser against different photosensitizers on tensile and shear bond strength of bonded composite to caries affected dentin

The Effects of Sodium Hypochlorite (5.25%), Chlorhexidine (2%), and Glyde File Prep on the Bond Strength of MTA-Dentin

Influence of Surface Pretreatment on the Bond Strength of a Resin Luting Cement to Saliva-contaminated Enamel and Dentin

Investigating the impact of surface treatments on tensile bond strength between pediatric prefabricated zirconia crowns and primary maxillary incisors with various types of luting cement: an in vitro study

Effect of immediate dentin sealing, bonding technique, and restorative material on the bond strength of indirect restorations

The Effects of Silver, Zinc Oxide, and Titanium Dioxide Nanoparticles Used as Dentin Pretreatments on the Microshear Bond Strength of a Conventional Glass Ionomer Cement to Dentin

Effects of Endodontic Irrigants on Shear Bond Strength of Mild Universal Adhesives to Dentin

Effect CPP-ACP/ACFP Pretreatment on Bond Strength of Resin Cements and Dentin

The Effect of Different Pre-Treatments on the Enamel Bonding Properties of a Self-Adhesive Resin Cement

Disinfection of caries affected dentin using rose bengal, titanium sapphire laser; ammonium hexa-fluorosilicate, and ozonated water on resin dentin bond strength