Abstract:Disordered preaggregation in liquid state during environmentally friendly printing of organic solar cells significantly limits device performance based on nonfullerene acceptors. Molecular side‐chain engineering can effectively tune this disordered preaggregation in liquid state, leading to enhanced crystallization with preferential face on molecular orientation, more efficient exciton dissociation and charge carrier transport, and finally good upscaling potential. The current power conversion efficiencies of laboratory‐sized organic solar cells (OSCs), based on the spin‐coating process with halogenated solvents, have exceeded 19%. Environmentally friendly printing is needed to bridge the gap between laboratory and industrialization by being compatible with roll‐to‐roll large‐area production. Here, the molecular design rules are revealed for enhancing the green printing potential of the state‐of‐the‐art photovoltaic martial systems by investigating the detailed structure formation dynamic and the key determining factors. By comparing two model systems based on D18:Y6 and D18:BTP‐eC9, it is found that disordered preaggregation in liquid state can result in over‐sized domains with reduced crystallinity and disordered molecular orientation, which significantly limits device performance. By systematically tuning the length of the inner alkyl side chains with multiple Y‐series materials, the authors demonstrate that molecular side‐chain engineering can effectively supress the detrimental disordered preaggregation in liquid state during environmentally friendly printing process, leading to enhanced crystallization with preferential faceon molecular orientation, more efficient exciton dissociation and charge carrier transport, and finally high upscaling potential. The work provides deeper insights into molecular engineering and structure formation dynamics toward environmentally friendly production of OSCs.

Suppressing Pre-Aggregation to Increase Polymer Solar Cell Ink Shelf Life

Unusual Performance Increase in Polymer Solar Cells by Cooling a Hot Donor/Acceptor Ink in a Good Solvent

Aqueous inks for ecofriendly processing of organic solar cells: investigation of morphological changes

Balancing the Molecular Aggregation and Vertical Phase Separation in the Polymer: Nonfullerene Blend Films Enables 13.09% Efficiency of Organic Solar Cells with Inkjet‐Printed Active Layer

Overcoming Disordered Preaggregation in Liquid State for Highly Efficient Organic Solar Cells Printed from Nonhalogenated Solvents

Simultaneous enhanced efficiency and thermal stability in organic solar cells from a polymer acceptor additive

Multiple Stabilization Effects of Benzylhydrazine on Scalable Perovskite Precursor Inks for Improved Perovskite Solar Cell Production

Thermal-Induced Performance Decay of the State-of-the-Art Polymer: Non-Fullerene Solar Cells and the Method of Suppression

Tuning polymer-backbone coplanarity and conformational order to achieve high-performance printed all-polymer solar cells

End‐extended Conjugation Strategy to Reduce the Efficiency‐Stability‐Mechanical Robustness Gap in Binary All‐Polymer Solar Cells

Solvent Inkjet Printing Process for the Fabrication of Polymer Solar Cells

Cold‐Aging and Solvent Vapor Mediated Aggregation Control toward 18% Efficiency Binary Organic Solar Cells

In‐situ Polymer Framework Strategy Enabling Printable And Efficient Perovskite Solar Cells by Mitigating "Coffee Ring" Effect

Extending Shelf‐life of Two‐step Method Precursor Solutions through Targeted Regulation for Highly Efficient and Reproducible Perovskite Solar Cells

Elimination of Drying‐Dependent Component Deviation Using a Composite Solvent Strategy Enables High‐Performance Inkjet‐Printed Organic Solar Cells with Efficiency Approaching 16%

Aging Iridium Oxide Catalyst Inks: A Formulation Strategy to Enhance Ink Processability for Polymer Electrolyte Membrane Water Electrolyzers

Flow-enhanced Solution Printing of All-Polymer Solar Cells

Optimized Active Layer Morphology Toward Efficient and Polymer Batch Insensitive Organic Solar Cells

Simultaneously Achieving Highly Efficient and Stable Polymer:Non‐Fullerene Solar Cells Enabled by Molecular Structure Optimization and Surface Passivation

Aggregation‐Induced Multilength Scaled Morphology Enabling 11.76% Efficiency in All‐Polymer Solar Cells Using Printing Fabrication

Accelerated Crystal Growth in >16% Printed MA x FA y Cs z PbI 3 Perovskite Solar Cells from Aqueous Inks