Abstract:A novel micro/nanoscale rough structured superhydrophilic hybrid-coated mesh that shows underwater superoleophobic behavior is fabricated by spray casting or dipping nanoparticle–polymer suspensions on stainless steel mesh substrates. Water droplets can spread over the mesh completely; meanwhile, oil droplets can roll off the mesh at low tilt angles without any penetration. Besides overcoming the oil-fouling problem of many superhydrophilic coatings, this superhydrophilic and underwater superoleophobic mesh can be used to separate oil and water. The simple method used here to prepare the organic–inorganic hybrid coatings successfully produced controllable micro-nano binary roughness and also achieved a rough topography of micro-nano binary structure by controlling the content of inorganic particles. The mechanism of oil–water separation by the superhydrophilic and superoleophobic membrane is rationalized by considering capillary mechanics. Tetraethyl orathosilicate (TEOS) as a base was used to prepare the nano-SiO2 solution as a nano-dopant through a sol-gel process, while polyvinyl alcohol (PVA) was used as the film binder and glutaraldehyde as the cross-linking agent; the mixture was dip-coated on the surface of 300-mesh stainless steel mesh to form superhydrophilic and underwater superoleophobic film. Properties of nano-SiO2 represented by infrared spectroscopy and surface topography of the film observed under scanning electron microscope (SEM) indicated that the film surface had a coarse micro–nano binary structure; the effect of nano-SiO2 doping amount on the film’s surface topography and the effect of such surface topography on hydrophilicity of the film were studied; contact angle of water on such surface was tested as 0° by the surface contact angle tester and spread quickly; the underwater contact angle to oil was 158°, showing superhydrophilic and underwater superoleophobic properties. The effect of the dosing amount of cross-linking agent to the waterproof swelling property and the permeate flux of the film were studied; the oil–water separation effect of the film to oil–water suspension and oil–water emulsion was studied too, and in both cases the separation efficiency reached 99%, which finally reduced the oil content to be lower than 50 mg/L. The effect of filtration times to permeate flux was studied, and it was found that the more hydrophilic the film was, the stronger the stain resistance would be, and the permeate flux would gradually decrease along with the increase of filtration times.

Facile fabrication of nanostructured titanium dioxide loaded graphene sheets coated ceramic membrane with superhydrophilic and underwater superoleophobic nature for water treatment

Disc Ceramic Membrane Modified with Nano-Tio2 for Separating Oil-Water Emulsion under Dynamic Membrane Filtration

Superhydrophilicity and Underwater Superoleophobicity TiO2/Al2O3 Composite Membrane with Ultra Low Oil Adhesion for Highly Efficient Oil-in-water Emulsions Separation

Preparation and Modification of Ceramic Membrane and Its Application in Oil/Water Wastewater Treatment

Enhanced photogenic self-cleaning of superhydrophilic Al2O3@GO-TiO2 ceramic membranes for efficient separation of oil-in-water emulsions

Preparation of Underwater Superoleophobic Membranes Via TiO2 Electrostatic Self-Assembly for Separation of Stratified Oil/water Mixtures and Emulsions

Preparation of super hydrophilic-underwater super oleophobic photoinduced self-cleaning Al 2 O 3 @TiO 2 ceramic membrane and separation performance of oil-in-water emulsion

Enhancement of super-hydrophilic/underwater super-oleophobic performance of ceramic membrane with TiO2 nanowire array prepared via low temperature oxidation

Superamphiphilic and underwater superoleophobic membrane for oil/water emulsion separation and organic dye degradation

Self-cleaning SiO 2 –TiO 2 ceramic membrane for enhanced oil–water separation

Potocatalytic antifouling membrane with dense nano-TiO2 coating for efficient oil-in-water emulsion separation and self-cleaning

A facile strategy for fabrication of nanocomposite ultrafiltration membrane: oily wastewater treatment and photocatalytic self-cleaning

Micro/Nanoscale Structured Superhydrophilic and Underwater Superoleophobic Hybrid-Coated Mesh for High-Efficiency Oil/Water Separation

Facile fabrication of silicon carbide decorated ceramic membrane, engineered with selective surface wettability for highly efficient separation of oil-in-water emulsions

Tannic Acid-Mediated Layered Double Hydroxide Hybridizing PVDF Superwetting Catalytic Membranes Constructed Via Ion Diffusion-Induced Interfacial Self-Assembly for Boosting Water Purification

3D-printed porous Al2O3 membrane coated with hydrophilic modified titanium dioxide particles for large-flux oil/water separation

A TiO 2 modified whisker mullite hollow fiber ceramic membrane for high-efficiency oil/water emulsions separation

Ceramic Membranes with Mussel-Inspired and Nanostructured Coatings for Water-in-oil Emulsions Separation

Micro-dissolved fabrication of robust superhydrophilic and underwater superoleophobic membranes based on cotton fabrics for oil/water separation

Integrated oil separation and water purification by a double-layer TiO 2-based mesh

Integrated oil separation and water purification by a double-layer TiO2-based mesh