Abstract:Good adhesive strength and joint durability are necessary for aluminum (Al)/polymer laminated film for lithium-ion battery packages. A modified propylene-based elastomer (mPBE) was prepared as the inner adhesive in this study. The polar group was grafted onto the PBE molecular chain via melt grafting with the assistance of styrene. The adhesive performance of PBE modified with glycidyl methacrylate is significantly higher than that of commercially available inner adhesives, Mitsui A and Dupont 739. Moreover, environmentally friendly trivalent chromium [Cr(III)] chemical conversion was used to treat Al foil and improve the adhesive joint. The wettability behavior of adhesive melt on the surface of Al foil was studied using high-temperature contact angle testing. The results indicate that wettability is not the sole factor impacting interfacial strength, surface energy of the adhesive melt also plays a role. To further study the effect of polar groups on the mPBE adhesion, a solvent casting-evaporation method was developed to prepare an ultra-thin mPBE coating on the Al foil surface. The morphology of mPBE-coated Al foils and the thickness of the coating were studied by atomic force microscope. The bonding mechanism at the interface was studied through time-of-flight secondary ion mass spectroscopy, and it was shown that the Cr(III) conversion coating could react with polar groups via acid-base interaction. Moreover, quantum chemical calculations based on density functional theory were used to reveal the bonding mechanism at the molecular level, and it is found that the adhesive strength is related to the electron-donor abilities and reactivity of the adhesive molecules.

Enhancing the interfacial bond strength of aluminum/polymer laminated film of the soft package lithium‐ion battery through polydopamine surface modification

Construction and Study on Corrosion Protective Property of Polydopamine-Based 3-Layer Organic Coatings on Aluminum Substrate

Polypropylene Separator Coated with a Thin Layer of Poly(lithium Acrylate‐co‐butyl Acrylate) for High‐performance Lithium‐ion Batteries

Self-Polymerized Dopamine Nanoparticles Modified Separators for Improving Electrochemical Performance and Enhancing Mechanical Strength of Lithium-Ion Batteries.

New insight into the interaction between maleic anhydride grafted polypropylene and aluminum foil converted with trivalent chromate: An experimental and DFT study

Effect of pretreatment on the interfacial bonding strength between modified polyolefin and aluminum foil treated with trivalent chromium chemical conversion: Experimental, quantum chemical calculations and molecular dynamics simulation

Experimental and Density Functional Theory Study of the Effect of Polar Groups on Interaction at the Polyolefin-Aluminum Laminated Film Interface

Effect of Modified Polypropylene on the Interfacial Bonding of Polymer–aluminum Laminated Films

Titanium Conversion Coatings on the Aluminum Foil AA 8021 Used for Lithium–ion Battery Package

Effect of Surface Pre-Treatment on the Hydrophilicity and Adhesive Properties of Multilayered Laminate Used for Lithium Battery Packaging

Surface Treatment and Adhesion Strength of Aluminum Foil for Lithium‐ion Battery Package

Improving the wettability and thermal resistance of polypropylene separators with a thin inorganic–organic hybrid layer stabilized by polydopamine for lithium ion batteries

Simple-effective strategy for surface modification via annealing treatment polydopamine coating

Microstructure and interaction in aluminum hydrides@polydopamine composites and interfacial improvement with GAP adhesive

An Adhesion Improvement of Low-Density Polyethylene to Aluminum through Modification with Functionalized Polymers

Polydopamine Hydrophilic Modification of Polypropylene Separator for Lithium Ion Battery

Growth Process of Molybdate Conversion Coating on the Surface of Aluminum Foil and Its Adhesive Mechanism

Molybdate-Based Conversion Treatment for Improving the Peeling Strength Between Aluminum Foil and Polypropylene Grafted with Glycidyl Methacrylate

Microstructure and Adhesion Properties of Cerium Conversion Coating Modified with Silane Coupling Agent on the Aluminum Foil for Lithium Ion Battery

High-Adhesion Ag Film with Enhanced Electromagnetic Shielding Performance via Post-Treatment of a Polydopamine Adhesive Layer

Ti/Cr(III) Conversion Coating on Aluminium Foil for Lithium-Ion Battery Package