Abstract:The synthesis of ammonia via Haber-Bosch process, obtained from nitrogen catalytic hydrogenation, was a great revolution for humankind that allowed mass production of food with the availability of fertilizers. 1 However, it caused a disturbance in the global nitrogen cycle due to the production of ammonia from a non-reactive source (N 2 ), fixing 10 8 tons of nitrogen into reactive species per year. 2 Among nitrogenous contaminants, nitrate is the main pollutant of wastewater and the most oxidized species, being accumulated in the ecosystems. 2 Besides that, because of the need of H 2 as reactant, the current ammonia production emits 500 million tons of carbon dioxide per year, making ammonia the largest CO 2 emitting chemical process. 1 Finding sustainable alternatives to restore the nitrogen cycle without compromising ammonia production and consequently food supply is urgently needed. 1,3 In this context, nitrate electrochemical reduction reaction (NO 3 RR) could be a sustainable way to produce ammonia, removing a pollutant from wastewater and helping ammonia decarbonization. 2,3 Finding a catalyst that presents high electrochemical performance, high availability, and good stability is still challenging. Among transition metals, copper has the fastest rate-determining step of nitrate reduction to nitrite, offering the highest electrocatalytic kinetics and exchange current densities for NO 3 RR. 4 In addition to metallic copper, its oxides are also attracting attention for catalytic NO 3 RR. 5–13 Different nanomaterials that combine copper metallic and oxide phases have been reported in the literature for ammonia synthesis, with Faradaic efficiencies up to 98%. 4 This enhancement is attributed to the fact that Cu 2 O requires lower activation energy to *NH 2 O hydrogenation, enabling the faster formation of *NH 2 OH at catalyst surface. 13 Our preliminary results show that there are also synergistic enhancements of Cu and Cu 2 O, i.e., a prepared mixture of Cu and Cu 2 O is more active than either compound alone. Herein, we investigate structural and compositional changes at a Cu/Cu 2 O nanocomposite after and during NO 3 RR. 14 Our findings suggest that under the potentials in which ammonia production from NO 3 RR takes place, Cu 2 O is also being reduced to Cu. Figure 1a presents linear sweep voltammetries (LSV) measurements with and without nitrate. LSV obtained in the absence of nitrate (black line) shows a peak related to Cu 2 O reduction (centered in -0.2 V vs. RHE). In the presence of nitrate (red line), the onset potential is around -0.1 V vs. RHE, from which a cathodic current takes place until -0.8 V vs. RHE. It indicates that Cu 2 O starts to reduce close to the onset potential for NO 3 RR. We evaluated the catalyst performance from -0.2 to -0.6 V vs. RHE and the highest faradaic efficiency (66 ± 7%) for NH 3 was obtained at -0.4 V vs. RHE (Figure 1b). Then, the composite was ex-situ characterized with spectroscopic and microscopic techniques before and after an 1h-electrolysis at -0.4 V vs. RHE. Though X-ray photoelectron spectroscopy, we show that copper oxidation state changes after potentiostatic electrolysis experiments at -0.4 V vs. RHE (Figures 1c and 1d), where the satellite peak related to Cu 2 O disappears. Significant structural changes were detected with atomic force microscopy (Figures 1e and 1f), evidenced by the change of the average roughness from 222.5 to 173.1 nm. In-situ Raman spectroscopy was employed to track copper oxidation state during NO 3 RR. Cu 2 O has some characteristic peaks at Raman spectra: 150 cm -1 related to infrared active mode F 1u (Τ 15 ), 520 cm -1 related to Raman allowed mode 3 T’ 25 ( F 2g ) and 630 cm -1 related to infrared active mode F 1u (Τ 15 ). 15 The spectra obtained (Figure 1g) showed that these peaks disappear at a less negative potential than the window that ammonia production from NO 3 RR takes place (-0.2 V vs. RHE), which is in accordance with LSV results, indicating that Cu 2 O reduces at a more positive potential than nitrate. These results suggest that higher activity for nitrate reduction could be associated with the formation of defects at composite structure, which will be evaluated later with kinetic studies. This work shows strong experimental indicatives that copper oxide is not stable at the potential window employed to ammonia production from NO 3 RR, although its reduction can induce some defects at copper structure that enhances the catalytic performance. These findings provide important clues towards designing new copper-based materials for electrochemical reduction of nitrate to ammonia. Figure 1

Effects of electrolyte pHs, temperatures, potentials and oxalate ions on the electrocatalytic reduction of nitrates

In Situ Loading of Cu2O Active Sites on Island-like Copper for Efficient Electrochemical Reduction of Nitrate to Ammonia.

Electrochemical behaviors and influence factors of copper and copper alloys cathode for electrocatalytic nitrate removal

Tracking Copper Oxidation State during Nitrate Electrochemical Reduction Reaction

Research Progress in Electrocatalytic Reduction of Nitrate to Ammonia by Copper-Based Materials

Identifying the Active Sites and Intermediates on Copper Surfaces for Electrochemical Nitrate Reduction to Ammonia

Insight into the Efficient Electrochemical Reduction of Nitrate Employing Pd/Ru Bimetallic Doped Copper Foam Cathode: Selectivity and Reliability

Enhanced Electrochemical Nitrate Reduction on Copper Nitride with Moderate Intermediates Adsorption

Optimizing Oxidation State of Octahedral Copper for Boosting Electroreduction Nitrate to Ammonia

Enhanced electroreduction of low-concentration nitrate using a Cu-Pd bimetallic cathode system: Performance evaluation, mechanism analysis, and potential applications

Effects of Ionic Interferents on Electrocatalytic Nitrate Reduction: Mechanistic Insight.

Modulating the Electrolyte Microenvironment in Electrical Double Layer for Boosting Electrocatalytic Nitrate Reduction to Ammonia

Selective and Efficient Electrocatalytic Synthesis of Ammonia from Nitrate with Copper‐Based Catalysts

High-Performance Electrochemical Nitrate Reduction to Ammonia under Ambient Conditions Using a FeOOH Nanorod Catalyst

Nano-Polycrystalline Cu Layer Interlaced with Ti3+-Self-Doped TiO2 Nanotube Arrays as an Electrocatalyst for Reduction of Nitrate to Ammonia

Recent developments in designing Cu-based electrocatalysts and advanced strategies for electrochemical nitrate reduction to ammonia

Regulating the Electrochemical Nitrate Reduction Performance with Controllable Distribution of Unconventional Phase Copper on Alloy Nanostructures

Rational design of electrocatalytic system to selective transform nitrate to nitrogen

Copper single-atom catalyst as a high-performance electrocatalyst for nitrate-ammonium conversion

Potential-Induced Synthesis and Structural Identification of Oxide-Derived Cu Electrocatalysts for Selective Nitrate Reduction to Ammonia

F-doped Cu-Fe Oxide nanosheets for effective electrocatalytic reduction of Nitrate to Ammonia