Abstract:Abstract 3D bioprinting is a recent technique that can create complex cell seeded scaffolds and therefore holds great promise to revolutionize the biomedical sector by combining materials and structures that more closely mimic the 3D cell environment in tissues. The most commonly used biomaterials for printing are hydrogels, however, many of the hydrogels used still present issues of printability, stability, or poor cell-material interactions. We propose that bioinks with intrinsic self-assembling and shear thinning properties, such as xanthan gum, can be methacrylated (XGMA) and combined with a bio-functional material such as gelatin methacryloyl (GelMa) to create a stable, cell-interactive bioink with improved properties for 3D bioprinting. These biomaterials have reduced viscosity under high shear and recover their viscosity rapidly after the shear is removed, retaining their shape, which translates to easier extrusion whilst maintaining accurate fidelity after printing. This was confirmed in printing studies, with measured normalized strand widths of 1.2 obtained for high gel concentrations (5+5 % XGMA-GelMA). Furthermore, the introduction of a secondary photo-cross-linking method allowed tuning of the mechanical properties of the hydrogel with stiffness between 15 and 30 kPa, as well as improving the stability of the hydrogel with retention of 75 % of its mass after 90 d. The hydrogel was shown to be biocompatible and bio-active with 97 % cell viability, and cell spreading after 7 d of culture for low gel concentrations (3+3 % XGMA-GelMA). Shear stresses were relatively low while printing (1 kPa) as a result of the shear thinning property of the material, which supported cell viability during extrusion. Finally, printed hydrogels retained high cell viability for lower gel concentrations, and showed improved cell viability for more concentrated hydrogels when compared to cells cultured in bulk hydrogels, presumably due to improved nutrient/oxygen diffusion and cell migration. In conclusion, stability and formulation of a XGMA-GelMA shear thinning composite hydrogel has been optimized to create a bio-functional bioink, with improved printability, and in vitro culture stability via secondary photo-induced cross-linking, making this composite a promising bioink for 3D bioprinting.

Use of Microfibrillated Cellulose/Lignosulfonate Blends as Carbon Precursors: Impact of Hydrogel Rheology on 3D Printing

Simulations of Extrusion 3D Printing of Chitosan Hydrogels

Dimethyl Sulfoxide Mediated High-Fidelity 3D Printing of Hydrogels

Formulation and characterization of an interpenetrating network hydrogel of locust bean gum and cellulose microfibrils for 3D printing

Research on the Printability of Hydrogels in 3D Bioprinting.

Printability of a Cellulose Derivative for Extrusion-Based 3D Printing: The Application on a Biodegradable Support Material

Assessing rheological properties of oxidized Moringa oleifera gum and carboxymethyl chitosan‐based self‐healing hydrogel for additive manufacturing applications

PREPARATION AND RHEOLOGICAL CHARACTERIZATION OF CELLULOSE-CHITOSAN HYDROGEL FOR EXTRUSION 3D PRINTER

Tuning Shear Thinning Factors of 3D Bio-Printable Hydrogels Using Short Fiber

Investigation of the 3D Printability of Covalently Cross-Linked Polypeptide-Based Hydrogels

Characterisation of hyaluronic acid methylcellulose hydrogels for 3D bioprinting

DLP 3D Printing Meets Lignocellulosic Biopolymers: Carboxymethyl Cellulose Inks for 3D Biocompatible Hydrogels

Chemical modification and printability of shear-thinning hydrogel inks for direct-write 3D printing

Evaluation of the printability of agar and hydroxypropyl methylcellulose gels as gummy formulations: Insights from rheological properties

Printability and bio-functionality of a shear thinning methacrylated xanthan–gelatin composite bioink

Single-Component Cellulose Acetate Sulfate Hydrogels for Direct Ink Writing 3D Printing

3D Printing of Multifunctional Hydrogels

Rheology in Product Development: An Insight into 3D Printing of Hydrogels and Aerogels

Rheological Study On 3d Printability Of Alginate Hydrogel And Effect Of Graphene Oxide

Preparation of a Novel Regenerated Silk Fibroin-Based Hydrogel for Extrusion Bioprinting.

DEAE- Cellulose-based composite hydrogel for 3D printing application: Physicochemical, mechanical, and biological optimization