Abstract:The growing demand for clean and efficient energy sources has been a direct result of the serious effect on the climate and the environment associated with high emissions of pollutants that are mainly produced by fossil fuel-based energy generators. Currently, green technology like proton exchange membrane fuel cells (PEMFC) can produce zero-emissions energy power by primarily using the electrochemical reactions of hydrogen and oxygen to generate electrical energy. Additionally, due to their high activity, Platinum (Pt) nanoparticles (NPs) distributed on a carbon catalyst support are considered the most efficient catalyst materials used in this technology. However, the main drawbacks of this technology are (i) the scarcity of Pt, making it very expensive for widespread fuel cell application and commercialization, and (ii) the susceptibility of the carbon support to corrosion and degradation when operating even at the most typical PEMFC conditions. Carbon corrosion can induce the loss of Pt NPs' active surface area when Pt detaches from the carbon support or agglomerates into larger Pt NPs, leading to premature performance losses in a PEMFC. In this work, we propose a novel approach to prevent carbon corrosion by selectively depositing a corrosion-resistant thin layer (~2 nm) of titanium nitride (TiN) only on the surface of the carbon support while the catalyst centers are left uncoated and accessible for reagent reactions (oxygen O and H + protons). TiN was used as the coating material because of its attractive properties, such as electronic conductivity, enough to enable the free movement of electrons from the current collector toward the catalytic centers. The TiN layer would also act as an anchoring mechanism of Pt NPs, preventing their mobility on the carbon support and subsequent agglomeration. The deposition of TiN layers was carried out at 150°C with a hollow-cathode plasma-assisted atomic layer deposition (HCPA-ALD) reactor and using tetrakis(dimethylamino)titanium (IV) as the metal precursor in Ar/N 2 plasma, from which nitrogen was used as the co-reactant. Before HCPA-ALD, to prevent TiN from depositing on top of the Pt NPs, the surface of Pt NPs was selectively coated with a thin film of oleylamine (OAm), a polymer that would only absorb onto Pt NPs, which is later removed from the catalyst system (after the HCPA-ALD process is finished) by heat treatment at 185°C. Here we will mainly focus on the TiN deposition process and the subsequent transmission electron microscopy (TEM) characterization performed on these nanoparticles, which allows us to prove the successful formation of homogenous coatings and architecture characteristics of these nanoparticles after oleylamine application and TiN deposition. Electrochemical characterization, including cyclic voltammetry (CV) and oxygen reduction reaction (ORR), was performed in a rotating disc electrode (RDE) to further confirm the activity and effectiveness of our designed catalyst. Our preliminary results have shown that highly conformal TiN can be successfully grown onto Pt/C nanoparticles (as powders) by using HCPA-ALD with a custom-made agitator mechanism. The second phase of this research will be focused on inspecting the degradation mechanisms this novel catalyst system experiences after potential cycling in a Membrane Electrode Assembly (MEA).

Modification of Physicochemical Properties of Platinum-Titanium Catalysts for Ammonia Slip Oxidation

Structure sensitivity of alumina- and zeolite-supported platinum ammonia slip catalysts

Theoretical Insights into Nitrate Reduction to Ammonia over Pt/TiO 2 : Reaction Mechanism, Activity Regulation, and Catalyst Design

A Facile Route for Spraying Preparation of Pt/TiO2 Monolithic Catalysts Toward VOCs Combustion

Selective Photocatalytic Oxidation of Gaseous Ammonia at Ppb Level over Pt and F Modified TiO2

Hydrothermal Synthesis of Platinum–Chromium Oxidation Catalysts on Metal Supports

Synthesis and Characterization of Platinum on Carbon Nanoparticles Selectively Coated with Titanium Nitride (TiN)

Pt Supported on Plasma-Chemical Titanium Nitride for Efficient Room-Temperature CO Oxidation

Nanostructured Platinum In Ordered Mesoporous Silica As Novel Efficient Catalyst For Propane Total Oxidation

Catalytic NH3 oxidation affected by the nanometric roughness of the platinum overlayer

Metal Oxide Inclusion in Polycrystalline Pt-Based Electrocatalyst for an Ammonia Oxidation Reaction

Effect of TiO2 Drying Conditions on the Catalytic Activity of Pt for Ammonia Synthesis from NO−H2

Electrochemical Properties of an Atomically Dispersed Platinum Catalyst Formed on a Heat-treated Carbon Support

Advancing nitrate reduction to ammonia: insights into mechanism, activity control, and catalyst design over Pt nanoparticle-based ZrO2

Controllable Synthesis of Supported Platinum Catalysts: Acidic Support Effect and Soot Oxidation Catalysis

Surface Oxidation of Ti3C2Tx Enhances the Catalytic Activity of Supported Platinum Nanoparticles in Ammonia Borane Hydrolysis

Robust Pt@TiO x /TiO 2 Catalysts for Hydrocarbon Combustion: Effects of Pt-TiO x Interaction and Sulfates

Enhanced performance of Nb2O5 decorated RuO2/Sn0.2Ti0.8O2 for selective catalytic oxidation of ammonia

Effect of Pretreatment Atmosphere on the Particle Size and Oxygen Reduction Activity of Low-Loading Platinum Impregnated Titanium Carbide Powder Electrocatalysts

In Situ X-ray Photoelectron Spectroscopy of Catalytic Ammonia Oxidation over a Pt(533) Surface

Effects of Platinum High-Temperature Redispersion on Pt/Al2o3 Diesel Oxidation Catalyst for Nitric Oxide Oxidation and Its Reaction Pathway