Abstract:A reliable accuracy is essential for the application of land surface temperature (LST) products. Current satellite retrieved LSTs are mainly validated over a few homogeneous sites. However, most of the existing ground sites are located in inhomogeneous areas: thus, their spatial representativeness on satellite pixel scales is unknown. In this situation, how to evaluate the spatial representativeness of these inhomogeneous sites, quantify the influence introduced by the spatial representativeness and describe the variation of the site's spatial representativeness are critical questions for satellite LST validation. In an attempt to answer those questions, a so-called temporal variation method (TVM) is proposed for evaluating a ground site's spatial representativeness. The method defines a spatial representativeness indicator (SRI), which is the LST difference between a ground radiometer's field-ofview (FOV) and a satellite pixel, and describes a site's spatial representativeness. Based on the temporal variation of LST, the SRI time series consists of three temporal components: increment ATC, increment DTCF-P, and increment USC, which describe the annual, diurnal, and instantaneous variations of SRI, respectively. Associated with the Landsat TM/ETM+ data and weather parameters, the method is implemented and tested at 16 Chinese ground sites for the validation of MODIS and AATSR LST products. Results show that the temporally continuous SRI (SRITPR) shows high correlations with the original SRI (SRIORI). The variation of SRITPR is mainly determined by changes in surface coverage (i.e. NDVI difference on the two scales) and affected by weather conditions (e.g. near-surface air temperature, accumulative downward solar radiation, and wind speed). Since the SRI is defined as the LST difference between the two scales, it can be used as a bridge to convert the in-situ LST to pixel scale to address the spatial scale mismatch in LST validation. With this idea, the in-situ LST at daytime was converted to pixel scale associated with the SRITPR, and the corresponding MODIS and AATSR LST were validated at the 16 ground sites. Results for MODIS and AATSR LST show that the effect of spatial representativeness on the validation results over the sites is large, with mean biases between -1.95 K and 5.60 K and standard deviations between 0.07 K and 3.72 K. Since the TVM method does not rely on a specific satellite or land surface product, it is readily applied to other LST products (e.g. Sentinel-3 SLSTR LST, NOAA VIIRS LST) and surface parameters (e.g. surface longwave radiation).

Validation of TROPOMI SIF Products With Improved Geolocation Match Between In Situ and Satellite Measurements

Quantification of uncertainty caused by geometric location mismatch in the validation of TROPOMI solar-induced chlorophyll fluorescence product

Intercalibration of Luojia1-01 and Suomi-NPP-VIIRS Monthly Nighttime Light Composite Using a Spatial-Temporal Residuals Correction Random Forest Model

A Geometric Location Matching Method for Validation of Satellite Products: A Case Study for Albedo.

Continuous Evaluation of the Spatial Representativeness of Land Surface Temperature Validation Sites

Evaluating the spatial representativeness of ground-based observations for satellite total ozone products

An Investigation on Inter-Calibrating EMI/GF-5 With TROPOMI/S5p in Ultraviolet–Visible Spectra

TROPOMI/S5P Total Column Water Vapor validation against AERONET ground-based measurements

Improved Vegetation Photosynthetic Phenology Monitoring in the Northern Ecosystems using Total Canopy Solar‐Induced Chlorophyll Fluorescence Derived from TROPOMI

On the Validity of Using Ground-Based Observations to Validate Geostationary-Satellite-derived Direct and Diffuse Surface Solar Irradiance: Quantifying the Spatial Mismatch and Temporal Averaging Issues

The First Assessment of Coarse-Pixel Soil Moisture Products Within the Multi-Scale Validation Framework over Qinghai-Tibet Plateau

Evaluation of remote sensing soil moisture data products with a new approach to analyse footprint mismatch with in-situ measurements

Retrieval of Red Solar-Induced Chlorophyll Fluorescence with TROPOMI on the Sentinel-5 Precursor Mission

Quantification of the Uncertainty Caused by Geometric Registration Errors in Multiscale Validation of Satellite Products

Impact of the Spatio‐Temporal Mismatch Between Satellite and In Situ Measurements on Validations of Surface Solar Radiation

Validation of downscaled 1‐km SMOS and SMAP soil moisture data in 2010–2021

An Improved Upscaling Method of in Situ Measurements with Consideration of Their Uncertainty for the Spatial Scale Match Between Satellite and in Situ Measurements.

Direct Comparison and Triple Collocation: Which is More Reliable in the Validation of Coarse‐Scale Satellite Surface Albedo Products

Mapping High Spatiotemporal-Resolution Soil Moisture by Upscaling Sparse Ground-Based Observations Using a Bayesian Linear Regression Method for Comparison with Microwave Remotely Sensed Soil Moisture Products

Geolocation Accuracy Validation of High-Resolution SAR Satellite Images Based on the Xianning Validation Field

Evaluating TROPOMI δD Column Retrievals With In Situ Airborne Field Campaign Measurements Using Expanded Collocation Criterion