Abstract:Laser-based metal additive manufacturing technology, which is represented by laser powder bed fusion (LPBF) and direct energy deposition (DED), has been widely used in high-end industries such as aerospace. However, with the rapid development of aerospace equipment, it has become increasingly difficult to meet the requirements of integrated design and manufacturing of metal parts by using LPBF or DED alone. LPBF/DED hybrid laser additive manufacturing technology is expected to greatly improve the overall manufacturing capacity of metal components by combining the advantages of the two technologies. It is expected to break through the limitation of overall manufacturing size, to realize the manufacturing of large and complex aerospace parts, and to reduce the number of components required for large and complex structures to meet the overall design and manufacturing requirements. In this paper, AlSi10Mg was selected as the build material for the LPBF/DED hybrid laser additive manufacturing process and the microstructure and mechanical properties of the as-built samples were studied. The analyses of the microstructure show that there are no obvious defects at the interface between the LPBF zone and the DED zone. Although the phase compositions of both the LPBF zone and the DED zone are composed of alpha-Al matrix and eutectic Si, the melt track shape, microstructural morphology, grain size, grain boundary angle distribution and grain texture change significantly around the LPBF/DED interface. The results of mechanical property tests indicated that the LPBF zone has higher microhardness and tensile strength but lower elongation in comparison with the DED zone. The fine microstructure containing a large number of Si-rich nano-precipitates and high amount of solid solution element enhance the microhardness and tensile strength of the LPBF zone, where the lower solid solubility and high percentage of low angle grain boundary increased the elongation of the DED zone. More importantly, the tensile strength of the LPBF/DED interface is not less than the DED zone, and the boundary of DED melt track as well as porosity defect in the DED zone are the weakest region of LPBF/DED hybrid laser additive manufacturing AlSi10Mg specimens. Therefore, the overall tensile strength of the sample is mainly determined by the DED zone. The formation mechanism of the gradient microstructure around the LPBF/DED interface and the effect of microstructure on properties were also analyzed. This paper proves that the LPBF/DED hybrid laser additive manufacturing technology can be used for the overall manufacturing of aluminum alloy components with regular surface structure.

Improvement of strength in single-lap adhesive joints of AlSi10Mg alloys fabricated by laser powder bed fusion

Fracture behavior of double edge notch AlSi10Mg alloy fabricated by laser powder bed fusion

Integrity Assessment of Electron‐Beam‐Welded Joints of Additively Manufactured AlSi10Mg Components

Effect of Aluminium Content and Processing Parameters on the Microstructure and Mechanical Properties of Laser Powder-Bed Fused Magnesium-Aluminium (0, 3, 6, 9wt%) Powder Mixture

Additive manufacturing of metal-polymer hybrid parts: the influence of as-printed LPBF surface roughness on the joint strength

Polymer-Metal Adhesion of Single-Lap Joints Using Fused Filament Fabrication Process: Aluminium with Carbon Fiber Reinforced Polyamide

Microstructure and mechanical properties of AlSi10Mg alloy built by laser powder bed fusion/direct energy deposition hybrid laser additive manufacturing

Adhesively bonded joints in components manufactured via selective laser melting

Additive Manufacturing of Al-12Si Alloy by Powder Laser Bed Fusion: an Investigation into its Microstructural Processes Formation and its Effects on Mechanical Behavior

Strength and failure mechanism of single-lap magnesium-basalt fiber metal laminate adhesively bonded joints: Experimental and numerical assessments

Review on the correlation between microstructure and mechanical performance for laser powder bed fusion AlSi10Mg

Joining of Aluminum and CFRP via Laser Powder Bed Fusion: Influence of Experimental Set-Up and Laser Processing on Microstructure and Mechanical Properties

Improving bonding strength of aluminium-PEEK hybrid metal-polymer joints by two-step laser surface treatment

Micromechanical Modeling of AlSi10Mg Processed by Laser-Based Additive Manufacturing: From as-Built to Heat-Treated Microstructures

Simultaneously enhanced strength and ductility of AlSi7Mg alloy fabricated by laser powder bed fusion with on-line static magnetic field

Machine-Learning Assisted Laser Powder Bed Fusion Process Optimization for AlSi10mg: New Microstructure Description Indices and Fracture Mechanisms

Optimization of microstructural morphology via laser processing to enhance the bond strength of Al-CFRP

A high Fe-containing AlSi12 alloy fabricated by laser powder bed fusion

Role of the solidification cells on the yield strength of the Al-Si-Mg alloy manufactured using laser powder bed fusion: A micropillar compression study

Research Status of Laser Powder Bed Fusion Al–Li Alloys and Its Improvement Measures

Nanosecond Laser-Induced Surface Modification to Strengthen Cu/Si3N4 AMB Joints