Abstract:The objective of the LuFo VI-1 project CATeW (Coupled Aerodynamic Technologies for Aircraft Wings) consists in multifidelity analyses to assess the potential for aerodynamic efficiency increase by combined application of hybrid laminar flow control and variable camber technologies to the wing of a transonic transport aircraft. Individually, both technologies have proven to lead to major aerodynamic drag reductions. An evaluation of the coupled technologies is, therefore, expected to show an even higher potential due to synergy effects. To derive conclusions on system level, low-fidelity (LowFi) overall aircraft design methodologies will be applied for the analysis of a medium haul reference aircraft in the course of the project, while complex aerodynamic phenomena are modelled with high-fidelity (HiFi) computational fluid dynamics methods. The paper at hand presents results of aerodynamic analyses on both fidelity levels for the wing of the turbulent reference configuration CATeW-01, featuring the technology combination as a retrofit. Furthermore, this work encompasses adaptations and implementations performed within both the LowFi and HiFi toolchains. The LowFi toolchain already incorporates several modules for the proposed technology combination. A short presentation of the LowFi-toolchain is given, along with the modeling approach in the HiFi framework using mesh deformations and a mass flux boundary condition. Comparative studies of the turbulent flow field around the wing show good agreement of predicted load distributions in both numerical frameworks, studies based upon the HiFi approach attest the potential for efficiency increase due to the variable camber technology, incorporated by means of Adaptive Dropped Hinge Flap (ADHF) deflections. Considering the coupled application, four different constant suction mass flow rates are examined, where the maximum mass flow causes laminar flow extending over the entire suction panel, thus moving the transition location from the wing's leading edge to the end of the suction panel. When being coupled with ADHF deflections, again the variable camber technology leads to a reduction of the wing's pressure drag component with the simultaneous application of boundary layer suction further promoting drag reduction with increasing suction rate. While the combined application shows no mutual inhibition, major reciprocal effects are not directly observable when applying the combination as a retrofit to the reference configuration CATeW-01. This is mainly attributed to the limited extend of laminar flow, thus indicating the necessity for optimization in wing geometry and operating parameters, to achieve extensive areas of laminar flow and to promote the aspired synergy effects.

Constraint analysis methodology for ground-effect vehicle conceptual design

An Assembly Gap Control Method Based on Posture Alignment of Wing Panels in Aircraft Assembly

Parametric Design Method and Lift/Drag Characteristics Analysis for a Wide-Range, Wing-Morphing Glide Vehicle

Low-fidelity method for rapid aerostructural optimisation and design-space exploration of planar wings

Sensitivity analysis of a Ground-Gen Airborne Wind Energy System design

Preliminary Analysis of the Stability and Controllability of a Box-Wing Aircraft Configuration

Topology Optimization for the Arm of Flight Simulator under Inertial Loads

Gappy POD model for Structural Compliance of the Wing of a Civil Tilt-rotor

Analysis of Flight Loads during Symmetric Aircraft Maneuvers Based on the Gradient-Enhanced Kriging Model

On Unsteady Effects in WIG Craft Aerodynamics

Absolute Nodal Coordinate Formulation With Vector-Strain Transformation for High Aspect Ratio Wings

Constraint-based parameterization using FFD and multi-objective design optimization of a hypersonic vehicle

Geometrically Nonlinear Aeroelastic Stability Analysis and Wind Tunnel Test Validation of a Very Flexible Wing

Unsteady aeroelastic characterization and scaling relations of flexible membrane wings

Prediction of Preliminary Maximum Wing Bending Moments under Discrete Gust

Embedding the Sensitivities of a Structural Surrogate in a Coupled Aerostructural Wing Optimization

Non-Linear Analysis in Post-Buckling Regime of a Tilt Rotor Composite Wing Structure Using Detailed Model and Robust Loading Approach

Analytic Solutions for Volume, Mass, Center of Gravity, and Inertia of Wing Segments and Rotors of Constant Density

Numerical analyses of a reference wing for combination of hybrid laminar flow control and variable camber

Multiobjective aerostructural optimization for efficient transport wing conceptual design

Investigation of Hybrid Laminar Flow Control Capabilities from the Flight Envelope Perspective