Abstract:Amassive number of lithium ion (Li-ion) batteries are used in electric vehicles and the number is still growing rapidly. Li-ion batteries are sensitive to temperature—they likely degrade in an over-cold or an over-hot environment. Battery thermal management systems (BTMSs) are designed to control the battery temperature within the optimal range between 20 and 55°C. Thermal management is one important part of battery management systems. A good BTMS allows researchers to improve the performance, extend the life, and enhance the safety of a battery. We launch this Research Topic to collect the latest technologies and design methodology on BTMSs. Three papers have been published in this issue. Yang et al. designed a semiconductor refrigeration system for a 48 V Li-ion battery pack which often operates at high discharge/charge rates, as shown in Figure 1A. A thermal model of the BTMS was also developed for this semiconductor-based BTMS. This BTMS is integrated with air cooling, limiting the maximum temperature to less than 40°C, as long as the temperature difference is less than 1.6°C. The semiconductor-based BTMS is effective when the battery temperature and discharge rate are high. Wang et al. applied a flat heat pipe (FHP) to a BTMS, utilizing the extremely high thermal dissipation ability of the FHP to remove the heat from the battery, as well as to improve the temperature homogeneity among battery cells. The BTMS structure is presented in Figure 1B. A thermal network model was also developed for this BTMS and the simulation agreed with the experiment data. The thickness, porosity, and particle diameter of a sintered wick on the thermal performance of the battery was investigated and the FHP was optimized. An FHP allows a radiator to be placed aside the battery pack as a condensation sector, making the battery pack compact. Luo et al. designed a novel direct liquid cooling BTMS. With a unique structure shown in Figure 1C, the BTMS can be used for cylindrical battery cells with water as the thermal fluid, without worrying about the potential risks of the electric conductivities of water. A numerical model was developed and validated with the system. They investigated the effects of the coolant flowrate and suggested a high flowrate (>500 mL/min) is needed for the discharge at a rate above 3C of a 20-cell module. Multiple inlets were also suggested to improve the temperature uniformity. These studies have shown new prototypes of battery cooling with semiconductors, heat pipes, and direct liquid cooling, which could provide alternatives for thermal management in commercial battery modules. Edited and reviewed by: Sheng S. Zhang, United States Army Research Laboratory, United States

Underwater Environmental Impact and Thermal Management of Unmanned Underwater Vehicle Li-Ion Batteries

An Intelligent Thermal Management System for Optimized Lithium-Ion Battery Pack

Theoretical and Experimental Investigations on Liquid Immersion Cooling Battery Packs for Electric Vehicles Based on Analysis of Battery Heat Generation Characteristics

Experimental and Numerical Study of PCM Thermophysical Parameters on Lithium-Ion Battery Thermal Management

Study on battery thermal management of autonomous underwater vehicle by bionic wave channels with liquid cooling

A Review of Thermal Management and Heat Transfer of Lithium-Ion Batteries

Thermal Design And Optimization Of Lithium Ion Batteries For Unmanned Aerial Vehicles

Editorial: Advanced Battery Thermal Management Systems

Thermal Management of Lithium-Ion Batteries Based on Honeycomb-Structured Liquid Cooling and Phase Change Materials

A comparative investigation of two-phase immersion thermal management system for lithium-ion battery pack

Design and Simulation of Passive Thermal Management System for Lithium-Ion Battery Packs on an Unmanned Ground Vehicle

AN INVESTIGATION INTO THE VIABILITY OF CELL-LEVEL TEMPERATURE CONTROL IN LITHIUM-ION BATTERY PACKS

Performance evaluation of a hydrostatic flow immersion cooling system for high-current discharge Li-ion batteries

Parametric Investigation on the Performance of a Battery Thermal Management System with Immersion Cooling

Investigation of the Liquid Cooling and Heating of a Lithium-Ion Battery Package for an Electric Vehicle

Recent Advances in Thermal Management Strategies for Lithium-Ion Batteries: A Comprehensive Review

Thermal management performance improvement of phase change material for autonomous underwater vehicles' battery module by optimizing fin design based on quantitative evaluation method

Preventing Thermal Runaway Propagation in Lithium-ion Batteries using a Passive Liquid Housing

Ultra-thin vapour chamber based heat dissipation technology for lithium-ion battery

Multi-Physics Numerical Analysis of Single-phase Immersion Cooling for Thermal Management of Li-Ion Batteries

Operando Ultrasonic Monitoring of the Internal Temperature of Lithium-ion Batteries for the Detection and Prevention of Thermal Runaway