Abstract:Combining two or more polymers as a blend is necessary rather than synthesizing new ones for the balance of polymer properties for end-use applications. This work introduces a sustainable polymer blend (matrix) for high-impact applications, as the accessibility and cost of production of these high-impact polymers keep souring. This was achieved by designing an experiment using design expert v10.0 to account for the number of experimental runs and optimise the polymer blend. Mechanical, dynamic mechanical, and temperature effects were considered on the blended polymer. Sixteen (16) experimental runs were generated with blend ratio as the independent variable and Impact Strength (IS) and Tensile Strength (TS) as the responses. The optimal blend ratio was obtained for wPP, PP and NR as 23, 30 and 47% respectively. While, the optimum conditions for maximum impact and tensile strengths from the D.E was 241.62 J/m and 118.04 MPa respectively, with a desirability of 0.973. While the validated values obtained were 248.9 J/m; with errors of 2.93% and 120.14 MPa; with an error of 1.75% respectively. Thermogravimetry analysis revealed a single peak degradation for sp17, sp18, and sp19 (control samples) while multiple degradation peaks were observed for the blends. It was believed to be a result of different times for degradation of the individual components forming the polymer blend. Also, the T d onset started around 300 °C and the T d offset was around 500 °C for all tested samples. While, the Dynamic Mechanical Analysis (DMA) showed that there was an improvement in the T g and damping factor for sp5 (109 °C, 0.171) as compared to sp17 and sp18 (81.1 °C, 0.089 and 104.3 °C, 0.061), but no improvement was recorded for storage and loss moduli. SEM micrographs showed a good surface morphology for the blend with optimal mechanical and thermal properties. The blend can be utilized for engineering applications, including matrices for body armour, helmets, car bumper, etc.

Characterization of the Mechanical, Biodegradation, and Morphological Properties of NBR/Biopolymer Blend, Integrated with a Risk Evaluation

Exploring the performance and biodegradability of Edible Biopolymer blends incorporating Pistacia atlantica subsp. Mutica Gum and Plasticized Poly(lactic acid)

Mechanical, physical and thermal properties of waste polypropylene/polystyrene/natural rubber (wPP/PS/NR) blends

Influence of Bio-Based Plasticizers on the Properties of NBR Materials

Investigation of Rheological, Morphological and Mechanical Properties, Thermal Stability, Biodegradability of the Dynamically Cured Natural Rubber/Polyester Blends

Performance evaluation of biodegradable polymer PHBV and PBAT blends with adjustable melt flow behaviour, heat deflection temperature, and morphological transition

Expanded bentonite clay by bio-adhesive resins and its impact on the mechanical, adhesion, and ultrasonic properties of NR/SBR/polyester cords systems

Production and functionalization strategies for superior polyhydroxybutyrate blend performance

Mechanical, thermal and morphological features of biodegradable crosslinked natural rubber latex- dextrin blends

Bio-Polyester/Rubber Compounds: Fabrication, Characterization, and Biodegradation

Biosourced Poly(lactic acid)/polyamide-11 Blends: Effect of an Elastomer on the Morphology and Mechanical Properties

A Comparative Study on the Aerobic Biodegradation of the Biopolymer Blends of Poly(butylene succinate), Poly(butylene adipate terephthalate) and Poly(lactic acid)

Effects of blending poly (polyol sebacate) and poly (polyol adipate) bioelastomers for soft tissue engineering in biomedical applications

Biodegradability, thermal, chemical, mechanical and morphological behavior of LDPE/pectin and LDPE/modified pectin blend

Partial Biodegradable Blend with High Stability against Biodegradation for Fused Deposition Modeling

Biodegradable polymer composite based on NBR rubber and protein waste

Green Biodegradable Thermoplastic Natural Rubber Based on Epoxidized Natural Rubber and Poly(butylene succinate) Blends: Influence of Blend Proportions

Thermo-Blending of Biobased Poly(propylene 2,5-furan dicarboxylate) and Poly(lactic acid) with Improved Mechanical Performance

Evaluation of the Physical and Shape Memory Properties of Fully Biodegradable Poly(Lactic Acid) (PLA)/Poly(Butylene Adipate Terephthalate) (PBAT) Blends

An investigation on the toughening behavior and morphology of acrylonitrile butadiene styrene/polybutylene terephthalate blends reinforced by carbon nanotubes

Biodegradable Polymers and Biodegradable Polymer Nanocomposites