Abstract:Besides conventional structuring processes such as turning, milling or photo-chemical etching, laser processes are increasingly being used for surface structuring of metals. These laser processes differ fundamentally in that structuring is carried out either by material removal or by material redistribution. In this study, a new hybrid process of material ablation by means of pulsed laser radiation and material redistribution based on a remelting process by means of cw laser radiation is experimentally investigated. Besides an introduction to this new hybrid process, we give a detailed description of the equipment and methods used as well as surface structures produced on Ti6Al4V. A melt pool was generated on a prepared Ti6Al4V surface using cw laser radiation with a laser beam diameter of 520 mu m, laser power of 220 W, and a scanning velocity of 100 mm/s. In order to create surface structures, simultaneously, superimposed pulsed laser radiation with a laser beam diameter of 65 mu m, pulse duration of 60 ns, a maximum pulse energy of 0.35 mJ, and a pulse frequency of 50 kHz was used to evaporate small amounts of molten material from the melt pool. This localized evaporation of molten material is assumed to create vapor pressure that deforms the melt pool surface and therefore leads to surface structures. Our results indicate that by pulsed laser radiation capillary surface waves with a wavelength of the doubled laser beam diameter are excited on the melt pool surface. This forced excitation of capillary surface waves result in surface structures that are analyzed after solidification by means of white light interferometry. Based on this analysis we derived an oscillation frequency of v = 2.27 (+/- 0.16) kHz for the excited capillary surface wave as well as an effective kinematic viscosity of mu= 0.1328 cm(2)s(-1) for the damping of this surface oscillation during solidification. In terms of structural features, we achieved surface structures with heights of up to 100 mu m. Furthermore, structure height controllably scales in dependence on pulse energy and number of laser pulses as long as no ejection of molten material takes place. Finally, a comparison of the redistributed material volume per time shows that we achieved a volume redistribution rate of 28.37 mm(3)/min, which is significantly bigger than has been achieved with other laser texturing techniques so far and demonstrates the high potential of this new hybrid technique not only for surface structuring purposes.

Ripple formation on TA2 pure titanium surface induced by annular laser beam at low pressure environment

Melt flow and ripple formation induced by continuous wave laser irradiating of copper foil at 10 Pa

Mechanism for Formation of Rippling Structure on Surface of Metallic Glasses Irradiated by Pulse Nanosecond Laser

Interplay of viscosity and surface tension for ripple formation by laser melting

Formation and Evolution of Micro/Nano Periodic Ripples on 2205 Stainless Steel Machined by Femtosecond Laser

Formation of Long- and Short-Periodic Nanoripples on Stainless Steel Irradiated by Femtosecond Laser Pulses

Formation, evolution and characterization of nanoporous structures on the Ti6Al4V surface induced by nanosecond pulse laser irradiation

Threshold effect on the femtosecond laser-induced periodic subwavelength structure: An analytical approach

Laser-induced surface structures at polymer surfaces irradiated by ns-UV-laser in water confinement and in air

Micro-Nano Scale Ripples On Metallic Glass Induced By Laser Pulse

Influence of Molten Pool Flow and Evaporation on the Surface Morphology During Laser Micro-Texture Processing

Experimental Investigation on a New Hybrid Laser Process for Surface Structuring by Vapor Pressure on Ti6Al4V

Numerical simulation and experimental study on laser micromachining of 304L stainless steel in ambient air

Generalized Model for Laser-Induced Surface Structure in Metallic Glass

Laser micro-texture formation mechanism based on modified heat-mass transfers and hydrodynamic models

Numerical Simulation of Effect of Different Initial Morphologies on Melt Hydrodynamics in Laser Polishing of Ti6Al4V

Numerical simulation and experimental analysis on nanosecond laser ablation of titanium alloy

Ripple Formation in Excimer Laser-Irradiated Silicon Dioxide/silicon System

Effects of oscillating molten pool flow on the weld formation and mechanical performance of titanium alloy joints

Numerical studies of melt pool and gas bubble dynamics in laser powder bed fusion process

Formation mechanism of pore defects and surface ripples under different process parameters via laser powder bed fusion by numerical simulation and experimental verification