Abstract:The aim of the study was to compare the properties of inulin hydrogels obtained with different methods, e.g., the traditional-thermal method and new, non-thermal methods, used in food production, like ultrasonic, high-pressure homogenization (HPH), and high hydrostatic pressures (HHPs). It was found that each of the compared induction methods allowed for obtaining inulin hydrogels. However, the use of non-thermal induction methods allows for obtaining a gel structure faster than in the case of thermal induction. In addition, hydrogels obtained with new, non-thermal methods differ from gels obtained with thermal treatment. They were characterized by higher stability (from 1.7 percent point-of-stability parameters for HHP 150 MPa to 18.8 for HPH II cycles) and in most cases, by improved microrheological properties-lower solid-liquid balance toward the solid phase, increased elasticity and viscosity indexes, and lowering the flow index. The gels obtained with the new, non-thermal method were also characterized by a more delicate structure, including lower firmness (the differences between thermal and non-thermal inductions were from 0.73 N for HHP at 500 MPa to 2.39 N for HHP at 150 MPa) and spreadability (the differences between thermal and non-thermal inductions were from 7.60 Ns for HHP at 500 MPa to 15.08 Ns for HHP at 150 MPa). The color of ultrasound-induced inulin gels, regarding the HPH and HHP technique, was darker (the differences in the L* parameter between thermal and non-thermal inductions were from 1.92 for HHP at 500 MPa to 4.37 for 10 min ultrasounds) and with a lower a* color parameter (the differences in the a* parameter between thermal and non-thermal inductions were from 0.16 for HHP at 500 MPa to 0.39 for HPH II cycles) and b* color parameter (the differences in the b* parameter between thermal and non-thermal inductions were from 1.69 for 5 min ultrasounds to 2.68 for HPH II cycles). It was also found that among the compared induction methods, the high-pressure technique has the greatest potential for modifying the properties of the created inulin hydrogels. Thanks to its application, depending on the amount of applied pressure, it was possible to obtain gels with very different characteristics, both delicate (i.e., soft and spreadable), using HHP at 150 MPa, and hard, using HHP at 500 MPa, the closest in characteristics to gels induced with the thermal method. This may allow the properties of hydrogels to be matched to the characteristics of the food matrix being created.

Textural, rheological and microstructural properties of imitation cheese containing inulin

Microstructural studies of imitation cheese with a shift in continuous phase

The physicochemical, texture hardness and sensorial properties of ultrafiltrated low-fat cheese containinggalactomannan and novagel gum

Inulin for Surimi Gel Fortification: Performance and Molecular Weight-Dependent Effects.

Use of micellar casein concentrate and milk protein concentrate treated with transglutaminase in imitation cheese products-Unmelted texture

Heat-induced inulin-gluten gel: Insights into the influences of inulin molecular weight on the rheological and structural properties of gluten gel to molecular and physicochemical characteristics

Effects of inulin with different polymerization degrees on the structural and gelation properties of potato protein

Effect of Inulin on Rheological Properties and Emulsion Stability of a Reduced-Fat Salad Dressing

Effect of inulin with different degree of polymerisation on textural and rheological properties of wheat starch - Effect of inulin on gel properties of starch

Rheological and Micro-Rheological Properties of Chicory Inulin Gels

Effect of inulin on texture and clarity of gellan gels

Mechanisms of inulin addition affecting the properties of chicken myofibrillar protein gel

Alteration of the structural properties of inulin gels

The influence of protein concentration on key quality attributes of chickpea-based alternatives to cheese

Effect of Pork Back Fat Replacement with Inulin Gel and Oat Bran Flour on the Physicochemical and Sensory Evaluation of a Leberkäse Meat Product

Effect of thermal and mechanical factors on rheological properties of high performance inulin gels and spreads

Thermal and Modern, Non-Thermal Method Induction as a Factor of Modification of Inulin Hydrogel Properties

Effects of inulin on the gel properties and molecular structure of porcine myosin: A underlying mechanisms study

Transglutaminase Crosslinked Milk Protein Concentrate and Micellar Casein Concentrate: Impact on the Functionality of Imitation Mozzarella Cheese Manufactured on a Small Scale Using a Rapid Visco Analyzer

Dairy by-Products Concentrated by Ultrafiltration Used as Ingredients in the Production of Reduced Fat Washed Curd Cheese

High-Performance Thin-Layer Chromatography-Immunostaining as a Technique for the Characterization of Whey Protein Enrichment in Edam Cheese