Analysis of Telescopic Belt Conveyor Tail Powered Dynamic Characteristics

Lian Zi-sheng

Abstract:Analyzed the main structure and hydraulic system of powered tail,control system set up by the passage of the dynamic equation and SIMULINK environment at the tail of the transfer process from the simulation analysis,in order to powered tail from the design of control system provides a theoretical basis.

Engineering

What problem does this paper attempt to address?

Design and Simulation of a Hydraulic System for Jumbo Screw Conveyors Based on Flow Compensation

Wang Lintao,Gong Guofang,Shi Hu

DOI: https://doi.org/10.3969/j.issn.1000-1212.2011.04.008

2011-01-01

Abstract:This screw type conveyor system is an important component of the soil pressure-balanced jumbo.Chip delivery rate within the enclosure compartment can be readjusted through altering RPM of the screw conveyor,while readjusting pressure within the enclosure compartment.The paper introduces a new type electro- hydraulic control system for the screw conveyor,which is based on a single pump for oil supply with flow compensation.You will find details of the work principles together with design and calculation of the hydraulic system.The analyses there are based on the control way with the flow compensation techniques.And finally,it tells how to carry out a relevant simulation study on the system by using an AMEsim soRware.RPM curves are available of the screw conveyor for comparison of flow compensation with those in non-flow compensation,so as to verify the system’s efficiency and fitness of the control method,thus providing reference data for the screw type conveyor system design in the jumbo machine.
Study of the Belt Conveyor Design Platform in the Power Plant Based on the Multidisciplinary Collaborative

Shijing Wu,Jia He,Xiaohua Luo,Kangkang Yang,Zenglei Zhang

DOI: https://doi.org/10.51758/agjsr-s1-2013-0024

2013-01-01

Arab Gulf Journal of Scientific Research

Abstract:In order to solve the low speed of information transmission, inefficient design and long development cycle in the design process of the belt conveyor in the thermal power plants, a multidisciplinary collaborative design System of the belt conveyor is put forward. With the analysis of the information requirement, integrated information model is established with systems accepted by user’s requirements through the network transmission protocol. Project managers can discuss and develop plans through the structure of distributed-centralized. By the framework of information interaction and conflict resolution, professional design personnel can exchange their information and finish the design of the belt conveyor collaboratively.
Development and Application of Telescopic Belt Conveyor Transfer Drive End Unit

Wang Hai-chuan

Abstract:By Workface telescopic belt conveyor tail using the traditional method of shrinking the problems in analysis,research system,has done a hydraulic Moving Self-move the tail and face the three applications,with the production of simple,easy to operate,input cost less,the labor intensity of small,safe and practical advantages and popularization.

Engineering
DESIGN AND DYNAMIC ANALYSIS OF A DRIVING SYSTEM FOR ROD-CABLE DEPLOYABLE MAST

苏斌,关富玲,杨大彬,杨治

DOI: https://doi.org/10.3969/j.issn.0254-6124.2004.04.011

2004-01-01

Abstract:The technique requirements, basic driving principles and designing methods of a motorized drive system for a kind of rod-cable deployable mast has been introduced in this paper. Three different kinds of driving system scheme are compared and the best one is chosen for the calculated model. Finally, the dynamic analysis of this mechanical system is presented.
Design of Binary Telescopic Belt Conveyor

Shi Tong-ju

Abstract:The binary telescopic belt conveyor design to adapt to the rapid development of the mining face. It completed the integral design of the conveyor by analysis the main part,such as nose gear, roller groove, central groove, belt, braking device, storage device. From the right angle choose the spare parts in order to realize the machine running effect optimal, and conform to the requirements of the development of long distance, high power, high capacity of the belt conveyor.

Engineering
On the design of telescopic system of belt conveyor

C. Lan,Baozhong Feng

DOI: https://doi.org/10.1117/12.2645476

2022-08-30

Abstract:Given that the disassembly speed of the body of the telescopic belt conveyor operated in an underground coal mine couldn’t keep consistent with the advancing speed of the working face, a telescopic system specially for the belt conveyor was designed. Then a detailed comparison of the merits and demerits and a force analysis of different telescopic systems were made in this paper. Lastly, a conveyor belt-oriented friction-type traction device was invented for specific working conditions. And the traction device is characterized by strong adaptability and high working efficiency and could retract and extend the telescopic part continuously and automatically, which provided an effective technical solution to facilitate the intelligent and efficient development of the modern mine.

Engineering
Structural analysis on telescopic middle frame of belt conveyor

Wang Shuan

Abstract:The telescopic middle frame of the belt conveyor is a new-type structural part, whose strength affects the operation of the whole telescopic belt conveyor system. ANSYS was applied to conduct FEA on the structure of the telescopic middle frame. After its 3D solid model being built, restraints and external loads were imposed on the system, and mesh division and solution completed. At last, the stress contours of the middle frame were obtained. FEA results indicated the telescopic middle frame of the belt conveyor met the design requirements in general, while the welding quality of the joint of walking mobile tail should be paid attention, so as to guarantee the reliable operation of the telescopic belt conveyor. Finally, the prototype was developed according to the analysis results.

Materials Science,Engineering
Dynamic characteristic analysis and startup optimization design of an intermediate drive belt conveyor with non-uniform load

Yu Feng,Miaotian Zhang,Guoping Li,Guoying Meng

DOI: https://doi.org/10.1177/0036850419881089

Abstract:As an important transportation equipment, belt conveyor plays an important role in underground coal mine production and is an indispensable component. In this article, taking the intermediate drive belt conveyor of Shanxi Tongmei Group Tongxin Mine as an example, the continuous dynamic method is adopted to comprehensively consider the non-uniform load distribution of the belt conveyor, and mathematical modeling of the intermediate drive belt conveyor is performed. The dynamic characteristics of the conveyor belt are analyzed. The MATLAB software is used to analyze the change of the conveyor belt tension under different starting accelerations. Based on the analysis results, the starting acceleration is optimized, and the new combined parabolic acceleration curve presented here is more suitable for the actual working condition of the belt conveyor. In this article, the startup timing of the head and middle motors of the belt conveyor is also discussed in depth. The start timing design of the belt conveyor is described, which provides a reference for the design of the belt conveyor with an intermediate drive.
Distributed Permanent Magnet Direct-Drive Belt Conveyor System and Its Control Strategy

Qixun Zhou,Hao Gong,Guanghui Du,Yingxing Zhang,Hucheng He

DOI: https://doi.org/10.3390/en15228699

IF: 3.2

2022-11-20

Energies

Abstract:The long-distance traditional belt conveyor driven by a single high-power motor has the problems of excessive tension increments and sharp fluctuations in speed and tension. This paper designs a distributed permanent magnet direct drive belt conveyor system. The dynamic model of the conveyor belt unit and the permanent magnet motor is analyzed. The multi-motor ring coupling control strategy and the double sliding film direct torque control strategy of the belt conveyor system are formulated. The mechanical-electrical coupling dynamic model of the belt conveyor system is built. Using MATLAB/Simulink modeling and simulation, the vector control strategy and electromechanical coupling dynamic behavior of the traditional belt conveyor system and the distributed permanent magnet direct drive belt conveyor system under light load start-up and local variable load operation conditions are studied. The results show that: the distributed permanent magnet direct drive belt conveyor system significantly reduces the peak of conveyor belt tension increment; the time spent under the starting light-load operation condition is shorter, and the fluctuation amplitude of speed and tension is smaller; it is possible to reduce the speed and tension fluctuation range of the conveying system and improve the robustness of the conveying system under local variable load conditions. Experiments have verified that increasing the number of drive motors in a conventional belt conveyor can suppress the disturbance caused by local load changes, and the distributed permanent magnet direct-drive belt conveyor has better dynamic regulation performance.

energy & fuels
Analysis and Design of the Roller for Belt Conveyor Based on ANSYS

Xing Qi Yuan,Shuang Yan Yang,Quan Yun Niu

DOI: https://doi.org/10.4028/www.scientific.net/amr.1027.315

2014-01-01

Advanced Materials Research

Abstract:With the fast development in continuous conveyor technology, the belt conveyor to be more widely applied, the belt conveyor technology is gradually refined, and has made a number of achievements. Drum as a belt conveyor drive components, attracted the attention of the relevant technical staff. To ensure the belt conveyor system, the optimizing design of the drum quality and the strengthen use of the drum performance have an important guiding significance to the safety and reliability as a whole. With the help of ANSYS software, finite element analysis, the optimal design results analysis showed that the effect of optimal design to achieve the purpose of has a certain guiding significance for optimizing the structure of actual production. Key words: Belt conveyor; drum; transmission parts; ANSYS; the optimization design
Design and Analysis of an Integrated Scope-varied Conveyer

LIU Xiangchen,GAO Ju

DOI: https://doi.org/10.3969/j.issn.1003-5311.2012.09.016

2012-01-01

Abstract:Based on the principles of processing an ultrasonic conveyer,we analyzed and designed an integrated scope-varied conveyer on the grounds of the theoretic principle of quadri-exit nets.So we deduced and obtain the equations of its transferring features and frequency for the integrated taper-transition of a ladder-shaped conveyer.In addition,with integrated CAD/CAE techniques,we adopted ways of integrating both parameter suppositions and the analysis of modes,and approached to the abstruse and theoretically complicated issue in designing an integrated scope-varied conveyer,coming to the solution to the facility of an implemented design of it.
Study on Speed and Torque Control of a Novel Hydromechanical Hybrid Transmission System in Wind Turbine

Wenting Chen,Yonggang Lin,Wei Li,Hongwei Liu,Le Tu,Hao Meng

DOI: https://doi.org/10.1049/iet-rpg.2018.6105

IF: 3.034

2019-01-01

IET Renewable Power Generation

Abstract:A wind turbine is the most typical machine used to capture energy from the wind. The system design goal of a wind turbine is to obtain as much energy as possible from the wind while transmitting as much of that energy to the grid as possible, all under the highest possible level of stability. Currently, many inherent weaknesses result in a high failure rate in common commercial wind turbines with gear drive systems. To improve the performance, in this study, a typical 1.5 MW gear transmission was redesigned into a novel hydromechanical transmission system (HMTS). Parameters related to the HMTS efficiency were analysed to ensure that the efficiency was relatively high. The variable speed ratio (VSR) and torque triple absorption (TTA) principle were thoroughly deduced. Moreover, a MATLAB/Simulink- AMESim cosimulation model was proposed, and a 30 kW proportional prototype was established. Both simulation and experimental results show that the structural design and proposed control strategies meet the design goals, including a relatively high transmission efficiency around the rated wind speed, speed control below the rated wind speed, and torque control above the rated wind speed. These achievements should guarantee the future application of the novel transmission system in wind turbines.
Scraper Conveyor Dynamic Modeling and Simulation

dong sheng zhang,x h liu,j g shi,jun mao,zhong li

DOI: https://doi.org/10.4028/www.scientific.net/AMR.217-218.426

2011-01-01

Abstract:Modeled nonlinearity, time-varying, dynamic coupling finite element model of scraper conveyor according to its actual working condition in the mining, studied the transmission mechanism of bulk material power and its parameters test methods, constructed the shape function of scraper conveyor circuitry, realized the computer automatic modeling, by the example carried on digital simulation of all of working condition such as starting, freely stoppage, abnormal load, chains blocked, the difference of chain's pitch and the chain wheel polygon effect, and so on.
A Compact Hydro-Mechanical Transmission Solution to Wheel Loader Propulsion System and Its Control Strategy

Feng Wang,Zhenchuan Lin,Haoxiang Zhang,Chen Zhang,Bing Xu

DOI: https://doi.org/10.1177/09544070231191157

2023-01-01

Abstract:Given the need for high efficiency to wheel loader powertrain, hydro-mechanical transmission is a promising solution to wheel loader propulsion system since it enables efficient engine operations owing to its continuously variable transmission function. The current hydro-mechanical transmission consists of planetary gear set and two hydrostatic units, making it bulky and complex in controls. This study proposes a simple and compact hydro-mechanical transmission solution to wheel loader powertrain. It improves vehicle acceleration performance by providing hydraulic torque assistance at low vehicle speed. The steady-state characteristics of the proposed hydro-mechanical transmission are analyzed, and the mathematical models of proposed wheel loader powertrain are constructed. An optimization strategy is developed as a reference for the design of an engine-speed based control strategy. The simulation results of the key components of proposed powertrain are analyzed. Furthermore, the engine-speed based control strategy is evaluated by the optimization strategy in different forms of the loading cycles. The results demonstrate the effectiveness of proposed wheel loader powertrain and its control strategy.
Analysis and Discussion on Tension of Long Transport Belt

Haojie Mu

DOI: https://doi.org/10.1051/matecconf/202338001024

2023-01-01

MATEC Web of Conferences

Abstract:The technical field of belt tensioning force studied in this paper, in particular, relates to a hydraulic belt tensioning device, including a base, a hydraulic system and a rail fixed on the base, and a tail wheel trolley sliding on the rail; This device can provide a large tension to the tail wheel of the conveyor belt to meet the tension required by the long conveyor belt. At the same time, it can automatically adjust the tension to the tail wheel of the conveyor belt according to the tension of the conveyor belt to realize the dynamic tension control of the conveyor belt; The device prevents belt deviation and material leakage, reduces labor intensity of workers, avoids equipment accidents, and improves industrial production capacity.
Analysis and research of dynamic characteristics of synchronous belt of a diesel using multi-body dynamics

Yimin Li,Zhiyong Hao,Jin Li

DOI: https://doi.org/10.4028/www.scientific.net/AMM.97-98.721

2011-01-01

Abstract:The dynamic tension of synchronous belt and pulleys forces are obtained by analyzing the dynamic characteristics of timing drive system of a diesel based on muti-body dynamics. The effects of crankshaft speed fluctuation and other excitations on the dynamics characteristics of synchronous belt are illustrated. After the analysis, it is found that crankshaft speed fluctuation has a great influence on the linear and transversal vibrations of synchronous belt. Comparing the simulation results of the original timing system and the one optimized, it is found that the modal frequency of synchronous belt depends on its span. Therefore it is important to control the span of belt and arrange the tensioner pulley properly for timing system design.
Finite ElementAnalysis of Driving Pulley of Belt Type Synch ronous Mechanism

Maomao Dai,Xiangying Meng,Minghang Ni,Jiean Liao,Wei Wang

DOI: https://doi.org/10.3969/j.issn.1003-188X.2015.06.006

2015-01-01

Abstract:Through analyzing the structure of the driving pulley of belt type synchronous mechanism of transplanting ma -chine ,the three-dimensional entity model of driving pulley was imported from PRO /E into ANSYS APDL finite element analysis software.Finite element model was built , and constraints and loads was applied , and then the comprehensive stress distribution and displacement distribution of the driving pulley was got as the result of the finite element numerical analysis .Then the force and deformation situation was mastered .With the checking and comparing with the parameters of the actual requirements , the danger zone and structural design flaws was determined , which provided scientific basis for the later design and optimization.
Dynamic Analysis of Tower Belt in Case of Changing Conveyer Direction

LAN Peng,LU Nian-li

DOI: https://doi.org/10.3969/j.issn.1006-7043.2006.03.006

2006-01-01

Abstract:A tower crane supported concrete conveyor belt system is an important piece of equipment for placing concrete.The conveyor belt changes direction with the help of the tower crane.A multi-body dynamic analysis was made of a large tower belt used at a construction site of the Three Gorges Dam in Hubei,China.Feasibility of this special operating mode,effect of the initial condition,and resultant shock were studied.Conveyers and steel wire were treated as moving flexible bodies,and a new explicit expression by finite element method(FEM) was developed.Motion equations of the conveyers,steel wire,and jib were assembled to form the system equation.The direction of conveyers could be changed during its swing motion after the jib was stopped.Analysis showed different critical initial slew velocities for different initial positions of the conveyer,and that the initial slew velocity must be greater than the critical value.Greater initial slew velocity caused greater vibration and a best range for initial condition was determined.
Belt Conveyor Dynamic Characteristics and Influential Factors

Junxia Li,Xiaoxu Pang

DOI: https://doi.org/10.1155/2018/8106879

IF: 1.616

2018-01-01

Shock and Vibration

Abstract:This paper uses the Kelvin-Voigt viscoelastic model to establish the continuous dynamic equations for tail hammer tension belt conveyors. The viscoelastic continuity equations are solved using the generalized coordinate method. We analyze various factors influencing longitudinal vibration of the belt conveyor by simulation and propose a control strategy to limit the vibration. The proposed approach and control strategy were verified by several experimental researches and cases. The proposed approach provides improved accuracy for dynamic design of belt conveyors.

engineering, mechanical,mechanics,acoustics
Dynamic Modeling and Simulation of Heavy Scraper Conveyor

MAO Jun,SHI Jian-guo,ZHANG Dong-sheng,WEI Xiao-hua

DOI: https://doi.org/10.3321/j.issn:0253-9993.2008.01.023

2008-01-01

Abstract:Studied the actual working and strained condition of scraper conveyor,established a nonlinear,time-variant,dynamic coupled finite element model of scraper conveyor,with taking into account the factors,such as the non-linear of chains,the elasticity and gap of scraper conveyor chute,and the mesh characteristic of chain and wheel.Constructed the shape function of scraper conveyor line,realized the computer automatic modeling.Through examples carried on digital simulation for such issues as starting,freely stopping,unusual load,chain block,the difference of chain's pitches and polygon effect of sprocket wheel's driving.The results indicate that it is the best means to reduce the starting fluctuant load by controlling starting types of conveyor.The tension distributing of chains before starting has a great influence on starting characteristic.The discrepancy between chain pitches badly affects power distribution of the double-driving scraper conveyor.The position of chain block has a decisive influence on the impact load,the less the teeth,the more obvious the polygon effect is.

Analysis of Telescopic Belt Conveyor Tail Powered Dynamic Characteristics

Design and Simulation of a Hydraulic System for Jumbo Screw Conveyors Based on Flow Compensation

Study of the Belt Conveyor Design Platform in the Power Plant Based on the Multidisciplinary Collaborative

Development and Application of Telescopic Belt Conveyor Transfer Drive End Unit

DESIGN AND DYNAMIC ANALYSIS OF A DRIVING SYSTEM FOR ROD-CABLE DEPLOYABLE MAST

Design of Binary Telescopic Belt Conveyor

On the design of telescopic system of belt conveyor

Structural analysis on telescopic middle frame of belt conveyor

Dynamic characteristic analysis and startup optimization design of an intermediate drive belt conveyor with non-uniform load

Distributed Permanent Magnet Direct-Drive Belt Conveyor System and Its Control Strategy

Analysis and Design of the Roller for Belt Conveyor Based on ANSYS

Design and Analysis of an Integrated Scope-varied Conveyer

Study on Speed and Torque Control of a Novel Hydromechanical Hybrid Transmission System in Wind Turbine

Scraper Conveyor Dynamic Modeling and Simulation

A Compact Hydro-Mechanical Transmission Solution to Wheel Loader Propulsion System and Its Control Strategy

Analysis and Discussion on Tension of Long Transport Belt

Analysis and research of dynamic characteristics of synchronous belt of a diesel using multi-body dynamics

Finite ElementAnalysis of Driving Pulley of Belt Type Synch ronous Mechanism

Dynamic Analysis of Tower Belt in Case of Changing Conveyer Direction

Belt Conveyor Dynamic Characteristics and Influential Factors

Dynamic Modeling and Simulation of Heavy Scraper Conveyor