Abstract:High contrast imaging can use pupil apodizers to suppress diffracted starlight from a bright source in order to observe its environs. Metallic half-tone dot transmissive apodizers were developed for the Gemini Planet Imager (GPI) and ESO SPHERE coronagraphs for use in the near-IR. Dot sizes on the scale of the wavelength of the light often result in unexpected variations in the optical transmission vs. superficial dot density relation. We measured 5 and 10 micron half-tone microdot screens' transmissions between 550 - 1050 nm to prepare to fabricate apodizations that mitigate diffraction by segments gaps and spiders on future large space telescopes. We utilized slow test beams (f/40, f/80) to estimate the on-axis (far-field, or zero-order) transmission of test patches using a Fourier Transform Spectrograph on Beamline U10B at Brookhaven National Laboratory's National Synchrotron Light Source (BNL NSLS). We also modified our previous GPI IR characterization hardware and methods for this experiment. Our measurements show an internal consistency of 0.1% in transmission, a factor of 5 better than our near-IR GPI work on the NSLS U4IR beamline. The systematics of the set-up appeared to limit the absolute calibration for our f/40 data on the 50-patch, maximum Optical Density 3 (OD3), sample. Credible measurements of transmissions down to about 3% transmission were achieved for this sample. Future work on apodizers for obstructed and segmented primary mirror coronagraphs will require configurations that mimic the intended diffractive configurations closely in order to tune apodizer fabrication to any particular application, and measure chromatic effects in representative diffractive regimes. Further experimental refinements are needed to measure the densest test patches which possess transmissions less than a few percent. The new NSLS-II should provide much greater spectral stability of its synchrotron beam, which will improve measurement accuracy and reduce systematics.

Design, analysis and test of a microdots apodizer for the Apodized Pupil Lyot Coronagraph

Design, analysis, and testing of a microdot apodizer for the Apodized Pupil Lyot Coronagraph. II. The dot size impact. (Research Note)

Calibrating Apodizer Fabrication Techniques For High-Contrast Coronagraphs On Segmented And Monolithic Space Telescopes

Phase-Apodized-Pupil Lyot Coronagraphs for Arbitrary Telescope Pupils

Exoplanet Imaging with a Phase-induced Amplitude Apodization Coronagraph III. Hybrid Approach: Optical Design and Diffraction Analysis

Performance characterization of a broadband vector Apodizing Phase Plate coronagraph

Phase-Induced Amplitude Apodization on Centrally Obscured Pupils: Design and First Laboratory Demonstration for the Subaru Telescope Pupil

A Binary Beam-Splitter For Lidar Beam-Shaping In Laser Imaging Application - Art. No. 66241j

Redundant apodization for direct imaging of exoplanets 2: Application to island effects

Apodized vortex coronagraph designs for segmented aperture telescopes

Interferometric apodization by homothety -- I. Optimization of the device parameters

On-sky performance analysis of the vector Apodizing Phase Plate coronagraph on MagAO/Clio2

Redundant Apodized Pupils (RAP) for high-contrast imagers robust to segmentation-due aberrations and island effects

Optimal pupil apodizations for arbitrary apertures

Zernike amplitude pupil apodization for vortex coronagraphy with obscured apertures

Development of binary shaped pupil mask coronagraph for the observation of exoplanets

Multi-Color Coronagraph Experiment in a Vacuum Testbed with a Binary Shaped Pupil Mask

Active correction of aperture discontinuities (ACAD) for space telescope pupils: a parametic analysis

Patterned liquid-crystal optics for broadband coronagraphy and wavefront sensing

Fast Linearized Coronagraph Optimizer (FALCO) IV. Coronagraph design survey for obstructed and segmented apertures

Diffraction-Based Sensitivity Analysis of Apodized Pupil Mapping Systems