Abstract:Carbon fiber reinforced polymer (CFRP) and titanium alloy (Ti-6Al-4V) have excellent mechanical properties and have been widely used in aviation, aerospace, and other fields. Due to the different characteristics of CFRP/Ti-laminated materials, there are differences in their processing parameters and material removal methods. Cutter wear and hole defects are prone to occur. To study the cutting performance of cutters in laminated materials, this paper adopts the inclined angle milling method to process CFRP/Ti-laminated materials. The cutting performance of flat end milling cutter and circular arc milling cutter was compared and analyzed through designed variable parameter experiments. A study was conducted on the axial force, cutter wear mechanism, hole quality, and micro-morphology of the hole wall of two cutters under the inclined angle milling method. The results show that under different processing parameters, the difference in axial force between the two cutters is small in the carbon fiber layer. However, there is a significant difference in the titanium layer, with the axial force of the circular arc milling cutter being smaller than that of the flat end milling cutter. As the number of holes increases, the wear of the flat end milling cutter is serious, and the cutting edge is broken. The wear area gradually expands from the cutter tip to the surrounding cutting edge. The wear of the circular arc milling cutter is relatively light, and the cutting edge is damaged. As the wear at the arc transition becomes dull, the wear area gradually extends to the surrounding cutting edge. As the cutters wear out, many burrs and tear damage appear at the CFRP exit of the flat end milling cutter. Many high burrs appeared at the exit of Ti-6Al-4V. Comparing the micro-morphology of the hole wall of the two cutters at different fiber cutting angles, the quality of the hole wall of the flat end milling cutter is worse than that of the circular arc milling cutter. Due to the arc transition structure of the circular arc milling cutter, the hole wall has obvious groove scratches, resulting in a decrease in the quality of the Ti-6Al-4V hole wall. In addition, compared with the flat end milling cutter, the surface roughness of the hole of the circular arc milling cutter is better.

A novel discrete-edge ball end milling cutter: Suitable for milling weakly rigid curved CFRP parts

Theoretical model of instantaneous milling force for CFRP milling with a ball-end milling cutter: Considering spatial dimension and temporal dimension discontinuity effects

Optimizing 5-Axis Tool Positioning and Orientation for Machining CFRP Curved Surfaces: Considering Fibers’ Orientation

An analytical approach to cutting force prediction in milling of carbon fiber reinforced polymer laminates

Milling Error Prediction of Thin-Walled Parts During High-Speed Machining

A Unified Geometrical Modeling and Analysis Method for Evaluating CFRP Machining Performance: Cutting Geometry Space

Partition Five-Axis Surface Machining of CFRP Laminate Structures Considering Fiber Orientation

An anti-wear tool structure with integrated-micro hybrid cutting edges for milling of carbon fiber–reinforced plastics composites

Experimental study on wear laws and mechanisms of end cutting edge in end-milling of carbon fiber reinforced polymer

Machining inclination selection method for surface milling of CFRP workpieces with low cutting-induced damage

Research on Tool Wear and Surface Integrity of CFRPs with Mild Milling Parameters

Prediction of time-varying dynamics and chatter stability analysis for surface milling of thin-walled curved CFRP workpiece

Considering the Bottom Edge Cutting Effect of the Carbon Fiber Reinforced Polymer Milling Force Prediction Model and Optimization of Machining Parameters

Planning of cutting tool feed direction for low-damage surface milling of CFRP: considering the changes in the action form of the tool edge on fiber

A novel reverse helical milling process for reducing push-out delamination of CFRP

Analysis of exit delamination mechanism and critical axial force in ball helical milling of CFRP

Investigating the material removal mechanism and cutting performance in ultrasonic vibration-assisted milling of carbon fibre reinforced thermoplastic

Simulation and Experimental Study on Reverse Helical Milling with the Gradual-Removal Reverse Edge Milling Cutter under Ultrasonic-Assisted Condition

Comparative study on cutting performance of CFRP/Ti-laminated materials with flat end milling cutter and circular arc milling cutter in inclined angle milling

Research on Subsurface Damage of CFRP Cutting with Biomimetic Gradient Micro-Textured Tools

Modeling of dynamic milling forces considering the interlaminar effect during milling multidirectional CFRP laminate