Abstract:This paper presents a summary of arsenic level statistics from air and wipe samples taken from studies conducted in fabrication operations. The main objectives of this study were not only to describe arsenic measurement data but also, through a literature review, to categorize fabrication workers in accordance with observed arsenic levels. All airborne arsenic measurements reported were included in the summary statistics for analysis of the measurement data. The arithmetic mean was estimated assuming a lognormal distribution from the geometric mean and the geometric standard deviation or the range. In addition, weighted arithmetic means (WAMs) were calculated based on the number of measurements reported for each mean. Analysis of variance (ANOVA) was employed to compare arsenic levels classified according to several categories such as the year, sampling type, location sampled, operation type, and cleaning technique. Nine papers were found reporting airborne arsenic measurement data from maintenance workers or maintenance areas in semiconductor chip-making plants. A total of 40 statistical summaries from seven articles were identified that represented a total of 423 airborne arsenic measurements. Arsenic exposure levels taken during normal operating activities in implantation operations (WAM = 1.6 μg m⁻³, no. of samples = 77, no. of statistical summaries = 2) were found to be lower than exposure levels of engineers who were involved in maintenance works (7.7 μg m⁻³, no. of samples = 181, no. of statistical summaries = 19). The highest level (WAM = 218.6 μg m⁻³) was associated with various maintenance works performed inside an ion implantation chamber. ANOVA revealed no significant differences in the WAM arsenic levels among the categorizations based on operation and sampling characteristics. Arsenic levels (56.4 μg m⁻³) recorded during maintenance works performed in dry conditions were found to be much higher than those from maintenance works in wet conditions (0.6 μg m⁻³). Arsenic levels from wipe samples in process areas after maintenance activities ranged from non-detectable to 146 μg cm⁻², indicating the potential for dispersion into the air and hence inhalation. We conclude that workers who are regularly or occasionally involved in maintenance work have higher potential for occupational exposure than other employees who are in charge of routine production work. In addition, fabrication workers can be classified into two groups based on the reviewed arsenic exposure levels: operators with potential for low levels of exposure and maintenance engineers with high levels of exposure. These classifications could be used as a basis for a qualitative ordinal ranking of exposure in an epidemiological study.

Source and characteristics of inorganic acidic gases and aerosols emission in a semiconductor plant

Emission and occupational health risk assessment of harmful contaminants in various processes in a typical semiconductor manufacturing industry building

Emission factors of air toxics from semiconductor manufacturing in Korea

Physicochemical Characteristics and Occupational Exposure of Silica Particles as Byproducts in a Semiconductor Sub Fab

Estimating Source Strengths of HCl and SO2 Emissions in the Flue Gas from Waste Incineration.

Exposure Assessment of Process By-Product Nanoparticles Released During the Preventive Maintenance of Semiconductor Fabrication Facilities

Study on characteristics of organic components in condensable particulate matter before and after wet flue gas desulfurization system of coal-fired power plants

Efficient control system for low-concentration inorganic gases from a process vent stream: application of surfactants in spray and packed columns

Investigation on Removal Effects and Condensation Characteristics of Condensable Particulate Matter: Field Test and Experimental Study.

Analysis and Control of Atmospheric Pollution Sources in “Two Acids”Plant

Non-methane hydrocarbons from integrated semiconductor manufacturing processes: Assessments of chemical footprints, emissions factors, and treatment efficiency

Removal Characteristics of Sulfuric Acid Aerosols from Coal-Fired Power Plants

Unexpectedly Increased Particle Emissions from the Steel Industry Determined by Wet/Semidry/Dry Flue Gas Desulfurization Technologies.

Advancements in greenhouse gas emission reduction methodology for fluorinated compounds and N2O in the semiconductor industry via abatement systems

A comprehensive review of arsenic levels in the semiconductor manufacturing industry

Evaluation of Potential Occupational Exposure and Release of Nanoparticles in Semiconductor-Manufacturing Environments

Emission characteristics of PM, heavy metals, and dioxins in flue gases from sintering machines with wet and semi-dry flue gas desulfurization systems

Eco-Friendly Dry-Cleaning and Diagnostics of Silicon Dioxide Deposition Chamber

A Study of SO2 Removal by Positive Pin-Plate Discharge System

Component Characteristics and Emission Factors of Volatile Organic Compounds from Dyestuff Production

Using a State-of-the-art Air Pollution Control System to Lower Pollutant Emissions