The Nylon Scintillator Containment Vessels for the Borexino Solar Neutrino Experiment

J. Benziger,L. Cadonati,F. Calaprice,E. de Haas,R. Fernholz,R. Ford,C. Galbiati,A. Goretti,E. Harding,An. Ianni,S. Kidner,M. Leung,F. Loeser,K. McCarty,A. Nelson,R. Parsells,A. Pocar,T. Shutt,A. Sonnenschein,R. B. Vogelaar

DOI: https://doi.org/10.1016/j.nima.2007.08.176

2007-02-20

Abstract:Borexino is a solar neutrino experiment designed to observe the 0.86 MeV Be-7 neutrinos emitted in the pp cycle of the sun. Neutrinos will be detected by their elastic scattering on electrons in 100 tons of liquid scintillator. The neutrino event rate in the scintillator is expected to be low (~0.35 events per day per ton), and the signals will be at energies below 1.5 MeV, where background from natural radioactivity is prominent. Scintillation light produced by the recoil electrons is observed by an array of 2240 photomultiplier tubes. Because of the intrinsic radioactive contaminants in these PMTs, the liquid scintillator is shielded from them by a thick barrier of buffer fluid. A spherical vessel made of thin nylon film contains the scintillator, separating it from the surrounding buffer. The buffer region itself is divided into two concentric shells by a second nylon vessel in order to prevent inward diffusion of radon atoms. The radioactive background requirements for Borexino are challenging to meet, especially for the scintillator and these nylon vessels. Besides meeting requirements for low radioactivity, the nylon vessels must also satisfy requirements for mechanical, optical, and chemical properties. The present paper describes the research and development, construction, and installation of the nylon vessels for the Borexino experiment.

Instrumentation and Detectors

What problem does this paper attempt to address?

The main problem that this paper attempts to solve is to design and implement a nylon scintillator container for the Borexino solar neutrino experiment to meet the requirements of an extremely low - radioactivity background. Specifically, the Borexino experiment aims to observe 7Be neutrinos with an energy of 0.86 MeV produced in the solar proton - proton chain reaction. To achieve this goal, it is necessary to ensure that the radioactivity levels of the scintillator (liquid scintillator) and the nylon container itself are extremely low, while meeting the requirements of mechanical, optical and chemical properties.

### Main problems:
1. **Reducing the radioactivity background**: The Borexino experiment has very strict requirements for the radioactivity background, especially for the scintillator and the nylon container. It is necessary to ensure that the radioactivity levels of these components are low enough to avoid interference with the neutrino signal.

2. **Material selection and characteristics**: The nylon film must have good chemical compatibility (compatible with the scintillator and the buffer liquid), mechanical strength (able to withstand the stress caused by buoyancy and temperature changes), optical transparency (not affecting the propagation of scintillation light), and low permeability (preventing radon gas from diffusing into the scintillator).

3. **Clean manufacturing process**: During the manufacturing and installation of the nylon container, strict cleaning measures must be taken to prevent the scintillator from being contaminated by dust and other radioactive impurities. For example, the amount of dust inside the inner container should not exceed 3 mg.

4. **Structural design and stability**: The design of the nylon container must take into account the buoyancy and gravity in different fluids to ensure that the container can remain stable during the experiment and will not drift or deform due to density differences.

5. **Monitoring and maintenance**: The nylon container needs to be equipped with monitoring instruments to monitor the temperature and pressure of the scintillator and the buffer liquid, as well as the shape and position of the container in real - time, ensuring the smooth progress of the experiment.

### Solutions:
- **Material selection**: A nylon film with a thickness of 125 µm was selected and specially treated to ensure that it has sufficient mechanical strength, optical transparency and low radioactivity.

- **Clean manufacturing**: All nylon films were precisely cleaned after production, and non - contact ultrasonic technology was used to remove surface particles to ensure that they meet strict cleaning standards.

- **Multi - layer protection**: Through the design of inner and outer nylon containers, external radioactive substances (such as radon gas) are prevented from entering the inner container, thus protecting the scintillator from pollution.

- **Mechanical analysis**: The stress distribution of the nylon container under different conditions was calculated by finite element analysis to ensure that it can withstand various stresses without breaking during the experiment.

In conclusion, this paper describes in detail the design, manufacturing and installation processes of the nylon container in the Borexino experiment, and solves the problem of how to achieve reliable neutrino detection under extremely low - background requirements.