Abstract:We are developing and investigating an Immunological Ion Sensitive Field Effect Transistor (Im-ISFET) based on graphene grown by CVD and subsequently transferred to desired substrates including transparent foils as in Fig. 1. This Im-ISFET allows us to measure both the current (I-V measurement) through the graphene and the capacitance (C-V measurement) on its surface [1].The measurement setup is schematically shown in Fig. 2. Through C-V measurement, the potential drop over the Electrical Double Layer (EDL) and the capacitance of it are obtained simultaneously. This gives more information about the adsorption of molecules on the graphene surface, and will forward our understanding of the binding of targets to the graphene surface which in turn will give us a deeper understanding of what the measured signals may tell. Performing C-V measurement with Si-based structures is difficult since a thick oxide layer is necessary to prohibit uncontrolled redox reactions on the surface. This oxide layer has a much smaller capacitance than the EDL capacitance. When measured in series with the EDL capacitance, the oxide capacitance dominates and renders the EDL capacitance undetectable. The use of graphene as the channel material overcomes this challenge. Graphene is much more chemically inert and does not need passivation against electrolytes. A capacitance measurement then only contains two terms: the quantum capacitance of graphene and the EDL capacitance. These two capacitance components are of the same order of magnitude and this enables capacitance measurement of the binding process. Our focus in this work is on DNA sensing. To make a DNA sensor, it is necessary to bind the DNA probe to the graphene surface via a linker layer. We have employed two different approaches to achieve this layer. One approach is to rely on a self-assembled monolayer (SAM) of an organic molecule 1-pyrenebutanoic acid succinimidyl ester (PYR-NHS)[2]. PYR-NHS has a pyrene group that binds to graphene through pi-pi stacking[3], and a carboxylic group activated by a succinimidyl ester that binds to the probe DNA. The functionalization is done through wet chemistry at room temperature and can be combined with in situ electrical measurements to characterize the coverage of the PYRNHS. The coverage is also measured by AFM, XPS, SEM, and fluorescence measurement. The fluorescence experiment is carried out by attaching the probe DNA onto a predetermined pattern and then measuring the fluorescence intensity of the labeled target DNA. The selectivity of DNA binding is characterized by measuring the fluorescence intensity on the spots with and without the probe DNA, as seen in Fig. 3. Characterization of the films will also be performed through XPS and SEM. Another approach is to deposit a thin layer of Au on graphene. The Au layer is so thin that it becomes non-percolating islands spread over the graphene surface. Thiol-based chemistry is then used to attach the DNA probe to the Au. The thiol-chemistry is well established for attaching organic molecules to Au in biochemistry. We have deposited Au layers of different nominal thicknesses by electron-beam evaporation, in order to find a suitable thickness window for sensing. The Au layers are characterized using SEM, grazing incident small angle x-ray scattering (GISAXS) and electrical measurements. An example of the GISAXS measurement is shown in the upper panel of Fig. 4, while the setup and working principle are illustrated in the lower panel of Fig. 4. References [1] Chen, S., et al., Applied Physics Letters, 101 (2012) 154106/1-3. [2] Ohno, Y., et al., Journal of the American Chemical Society, 132 (2010) 18012–3. [3] Chen, R. J., et al., Journal of the American Chemical Society, 123 (2001) 3838–9. Au 4

Modification in Adsorption Properties of Graphene During the Development of Viral Biosensors

Biolayer-Interferometry-Guided Functionalization of Screen-Printed Graphene for Label-Free Electrochemical Virus Detection

High enhancement of sensitivity and reproducibility in label-free SARS-CoV-2 detection with graphene field-effect transistor sensors through precise surface biofunctionalization control.

Highly sensitive graphene biosensors based on surface plasmon resonance.

Human virus detection with graphene-based materials

Recent advances in graphene-based biosensor technology with applications in life sciences

Quality Assessment of Processed Graphene Chips for Biosensor Application

Role of Graphene in Surface Plasmon Resonance-Based Biosensors

Insights into the conformation changes of SARS-CoV-2 spike receptor-binding domain on graphene

Functionalization of Graphene towards Dual-Mode Bio-Sensing

A Brief Review of Graphene-Based Biosensors Developed for Rapid Detection of COVID-19 Biomarkers

Synthesis of exfoliated multilayer graphene and its putative interactions with SARS-CoV-2 virus investigated through computational studies

Ultrasensitive Biochemical Sensing Platform Enabled by Directly Grown Graphene on Insulator

Investigation and comparison of graphene nanoribbon and carbon nanotube based SARS-CoV-2 detection sensors: An ab initio study

Performance Enhancement of SPR Biosensor Using Graphene–MoS2 Hybrid Structure

Design and finite element modeling of two-dimensional nanomechanical biosensors for SARS-CoV-2 detection

Graphene-based optical sensors for the pre-vention of SARS-CoV-2 viral dissemination

Structural behavior of monomer of SARS-CoV-2 spike protein during initial stage of adsorption on graphene

Bridging basic science and applied diagnostics: Comprehensive viral diagnostics enabled by graphene-based electronic biosensor technology advancements

FEM simulation of SARS-CoV-2 sensing in single-layer graphene-based bionanosensors

The adsorption effect on chemical kinetics at the reaction surface in a microfluidic channel of a biosensor for the SARS-Cov-2 detection