Abstract:Lithium–sulfur (Li–S) batteries are severely hindered by the low sulfur utilization and short cycling life, especially at high rates. One of the effective solutions to address these problems is to improve the sulfiphilicity of lithium polysulfides (LiPSs) and the lithiophilicity of the lithium anode. However, it is a great challenge to simultaneously optimize both aspects. Herein, by incorporating the merits of strong absorbability and high conductivity of SnS with good catalytic capability of ZnS, a ZnS-SnS heterojunction coated with a polydopamine-derived N-doped carbon shell (denoted as ) with uniform cubic morphology was obtained and compared with the ZnS-SnS2@NC heterostructure and its single-component counterparts ( and SnS2@NC). Theoretical calculations, ex situ XANES, and in situ Raman spectrum were utilized to elucidate rapid anchoring-diffusion-transformation of LiPSs, inhibition of the shuttling effect, and improvement of the sulfur electrochemistry of bimetal ZnS-SnS heterostructure at the molecular level. When applied as a modification layer coated on the separator, the cell with optimized lithiophilicity and sulfiphilicity enables desirable sulfur electrochemistry, including high reversibility of 1149 mAh g–1 for 300 cycles at 0.2 C, high rate performance of 661 mAh g–1 at 10 C, and long cycle life with a low fading rate of 0.0126% each cycle after 2000 cycles at 4 C. Furthermore, a favorable areal capacity of 8.27 mAh cm–2 is maintained under high sulfur mass loading of 10.3 mg cm–2. This work furnishes a feasible scheme to the rational design of bimetal sulfides heterostructures and boosts the development of other electrochemical applications.The Supporting Information is available free of charge at <a class="ext-link" href="/doi/10.1021/acsnano.1c00270?goto=supporting-info">https://pubs.acs.org/doi/10.1021/acsnano.1c00270</a>.Additional experimental sections (materials synthesis, characterizations, and DFT calculations); SEM, TEM, XRD, TG, XPS, BET, and XANES characterizations of the samples; CV curves; discharge–charge profiles and cycle performance of various electrodes; in situ Raman tests; optimized geometries of LiPSs; Tables S1–S6: Li+ diffusion rates, EIS fitting, and comparisons of electrochemical performance (<a class="ext-link" href="/doi/suppl/10.1021/acsnano.1c00270/suppl_file/nn1c00270_si_001.pdf">PDF</a>)This article has not yet been cited by other publications.

Ultrathin NiO/Ni3S2 Heterostructure as Electrocatalyst for Accelerated Polysulfide Conversion in Lithium–Sulfur Batteries

Selective Adsorption and Electrocatalysis of Polysulfides Through Hexatomic Nickel Clusters Embedded in N-Doped Graphene Toward High-Performance Li-S Batteries

Rich Heterointerfaces Enabling Rapid Polysulfides Conversion and Regulated Li2S Deposition for High-Performance Lithium-Sulfur Batteries.

Rational Design of a Ni3N0.85 Electrocatalyst to Accelerate Polysulfide Conversion in Lithium-Sulfur Batteries

Vanadium nitride nanocrystals decorated ultrathin, N-rich and hierarchically porous carbon nanosheets as superior polysulfides mediator for stable lithium-sulfur batteries

A hollow Co0.12Ni1.88S2/NiO heterostructure that synergistically facilitates lithium polysulfide adsorption and conversion for lithium-sulfur batteries

Accelerated Polysulfide Conversion by Rationally Designed NiS2‐CoS2 Heterostructure in Lithium–Sulfur Batteries

Efficient Catalysis of Ultrathin Two-Dimensional Fe2 O3 -CoP Heterostructure Nanosheets for Polysulfide Redox Reactions

Coupling highly dispersed Sb2S3 nanodots with nitrogen/sulfur dual-doped porous carbon nanosheets for efficient immobilization and catalysis of polysulfides conversion

Efficient Catalysis of Ultrathin Two-Dimensional Fe2O3-CoP Heterostructure Nanosheets for Polysulfide Redox Reactions

Bimetallic sulfides heterostructure efficient adsorption and catalytic of polysulfides for high-performance lithium-sulfur batteries

ZnS-SnS@NC Heterostructure as Robust Lithiophilicity and Sulfiphilicity Mediator toward High-Rate and Long-Life Lithium–Sulfur Batteries

Synergistic catalysis of MoS2-Ni3S2 heterojunctions to accelerate polysulfide conversion for high-performance Li-S battery

Efficient Ni2Co4P3 Nanowires Catalysts Enhance Ultrahigh‐Loading Lithium–Sulfur Conversion in a Microreactor‐Like Battery

A High‐Efficiency CoSe Electrocatalyst with Hierarchical Porous Polyhedron Nanoarchitecture for Accelerating Polysulfides Conversion in Li–S Batteries

Surface reconstruction on Ni2P@CC to form an ultrathin layer of Ni(OH)2 for enhancing the capture and catalytic conversion of polysulfides in lithium–sulfur batteries

Mastering Surface Sulfidation of MnP‐MnO2 Heterostructure to Facilitate Efficient Polysulfide Conversion in Li─S Batteries

A rational design of V2O3/VN heterostructures with high-efficient chemisorption and electrocatalytic activity for polysulfides in lithium-sulfur batteries

NiMoO 4 Nanosheets Anchored on NS Doped Carbon Clothes with Hierarchical Structure as a Bidirectional Catalyst toward Accelerating Polysulfides Conversion for LiS Battery

Furnishing Continuous Efficient Bidirectional Polysulfide Conversion for Long‐Life and High‐Loading Lithium–Sulfur Batteries via the Built‐In Electric Field

Heterostructured nickel–cobalt metal alloy and metal oxide nanoparticles as a polysulfide mediator for stable lithium–sulfur full batteries with lean electrolyte