Abstract:This study proposes a clustered dynamic adaptive chemistry (CDAC) method, which uses an iterative K-means algorithm to partition the computational cells into different groups according to their similarity in terms of the temperature and significant species compositions. Taking advantage of the clustered cells, the averaged thermo-chemical properties of the cells in the respective clusters are then used to identify the adaptive dynamic reduced chemistry through the method of direct relation graph with error propagation (DRGEP). Moreover, the integration of the chemical source term, which commonly dominates the computational effort in reactive flow simulations, is now performed using the dynamic adaptive reduced chemistry at the cluster level instead of the cell level. With this CDAC method, the on-the-fly DRGEP process as well as the chemistry integration only needs to be conducted at the cluster level, dramatically reducing the unnecessary repeated computation for similar computational cells. In addition, the adaptive dynamic reduced chemistry further accelerates the chemistry integration process due to less ordinary differential equations (ODEs) to be solved for each cluster. This newly proposed CDAC method was tested in multi-dimensional homogeneous charged compression ignition engine (HCCI), direct injection compression ignition (DICI) engine and constant volume chamber combustion (CVCC) fueled with diesel, biodiesel and kerosene through the use of their respective surrogate fuel mechanisms under different operating conditions. The performance of CDAC in terms of accuracy and efficiency were extensively analyzed and discussed using different user-defined parameters, mechanisms with different surrogate components and number of species as well as different meshes with different number of grid cells. Based on this analysis, the error tolerances in DRGEP and the error tolerances of the temperature and significant species' mass fraction are recommended as: epsilon(d) <= 0.001, epsilon(T) 20K and epsilon(Y) <= 0.01 to achieve less than 0.1% integral error. With these recommended user-defined tolerances, it can be observed that the current CDAC method is able to accurately predict the in-cylinder pressure as well as the species profile in HCCI, DICI and the flame lift-off length in CVCC when compared with the full chemistry calculations as well as the experimental results. Moreover, with the recommended user defined error tolerances and a chemical kinetic model of 112 species, this CDAC method is capable of achieving a computational time speed-up factor of more than 3 compared to the conventional DAC and of almost 5 compared to the full chemistry. Finally, the CDAC method coupled CFD was applied to simulate a diesel DICI engine under three different engine speeds with a detailed primary reference fuel (PRF) mechanism of more than 1000 species. The 3-D simulation could be finished in acceptable CPU time while being able to well capture the experimental in-cylinder pressure and heat release rate for all the three engine speeds. (C) 2018 The Combustion Institute. Published by Elsevier Inc. All rights reserved.

A Line-Search-Based Algorithm for Multiphase Flash Calculations with CO 2 -Hydrocarbon System

A Novel Method to Accelerate the Three-phase Flash Calculation of the Hydrocarbon-CO 2 System

A Membrane Computing Optimization Algorithm with Multi-Subsystems for Parameter Estimation of Heavy Oil Thermal Cracking Model

Artificial neural network assisted two-phase flash calculations in isothermal and thermal compositional simulations

Artificial Neural Network Accelerated Flash Calculation for Compositional Simulations

Computational Acceleration of Multi-Dimensional Reactive Flow Modelling Using Diesel/biodiesel/jet-Fuel Surrogate Mechanisms Via a Clustered Dynamic Adaptive Chemistry Method

DL-KF Modeling for Acceleration of Flash Calculations in Phase Equilibrium Using Deep Learning Methods

Rapid multi-component phase-split calculations using volume functions and reduction methods

A Practical Compositional Method for Simulation of CO2 Flooding in Porous and Fractured Petroleum Reservoirs

Model Formulation for Compositional Numerical Simulation of CO2 Flooding in Fractured Reservoirs

Modelling and Simulation on Compressible Multi-Component Gas-Liquid Flows with Chemical Reaction and Phase Transition Effects

Composable Design of Multiphase Fluid Dynamics Solvers in Flash-X

An Advanced General Dominant Eigenvalue Method of Accelerating Successive Substitution During FLash Calculation for Compositional Reservoir Model

The artificial neural network-based two-phase equilibrium calculation framework for fast compositional reservoir simulation of CO 2 EOR

A Dynamic Multi-Timescale Method for Combustion Modeling with Detailed and Reduced Chemical Kinetic Mechanisms

Multilevel Adaptive Methods for Turbulent Combustion with Detailed Chemistry: Part I

Sequential Scheme of Full Composition Model for CO2 Flooding in Adaptive-Mesh System

A self-adaptive deep learning algorithm for accelerating multi-component flash calculation

An Enhanced Compressible Two-Phase Flow Model with Detailed Chemistry under the Adaptive Mesh Refinement Frame

Energy landscape analysis for two-phase multi-component NVT flash systems by using ETD type high-index saddle dynamics

A homogeneous relaxation model algorithm in density-based formulation with novel tabulated method for the modeling of CO 2 flashing nozzles