Abstract:Alkali-activated binders (AABs) have been and continue to be extensively explored as an alternative to ordinary Portland cement (OPC), addressing environmental and sustainability issues. A large number of studies that were conducted earlier focused mainly on the mechanical properties and some durability aspects of industrial waste-based AABs. However, chloride migration and diffusion causing reinforcement corrosion in AAB-based concrete (AAC) have not been thoroughly investigated. The present study focuses on the durability of AAC produced using multiple precursors that included industrial waste materials and natural minerals such as limestone powder (LSP), red mud (RM), silicomanganese fume (SMF), and natural pozzolan (NP) activated by alkali. Firstly, the dosages of all four precursors were optimized through trials and then NP was partially replaced by 10, 20 and 30% OPC to enhance the performance of the AABs. The AAC mixtures were prepared and cured under different conditions and tested for compressive strength and durability characteristics related to chloride permeability, chloride migration, chloride diffusion, and chloride-induced reinforcement corrosion to evaluate the performances of the mixtures. The results show that the composition of the AABs and curing regimes significantly influenced the performance of the AAC. The inclusion of the OPC resulted in a very significant enhancement of the strength and durability characteristics of the AAC. In addition, there is a sharp increase in the performance of the AAC mixtures when the OPC content of the precursor was increased from 10 to 20%, irrespective of the curing method. Therefore, an optimum dosage of the OPC in the precursor can be considered as 20%, allowing utilization of 80% waste materials and natural minerals as the precursor with much higher strength and durability characteristics than traditional OPC concrete, thus saving energy and reducing environmental pollution leading to a cleaner production of concrete. Lastly, electrochemically measured corrosion potential ( E corr ) and corrosion current density ( I corr ) values for the reinforcing bars (rebars) embedded in AAC mixtures were found to be misleading, as confirmed by visual inspection of the extracted rebars in addition to gravimetric test results. Hence, there is a need for further research to develop corrective measures before the utilization of the electrochemical-reinforced corrosion monitoring methods in the case of AACs.

Mix design and mechanical properties of geopolymer and alkali activated concrete: Review of the state-of-the-art and the development of a new unified approach

A review on alkali-activated binders: Materials composition and fresh properties of concrete

A mix design methodology of blast furnace slag and fly ash-based alkali-activated concrete

Properties of Alkali-Activated Concrete Made Using the Optimum Combinations of Precursor Materials and Activation Parameters

Strength prediction and mix design procedures for geopolymer and alkali-activated cement mortars comprising a wide range of environmentally responsible binder systems

Study of mix design and performance of alkali-activated concrete with recycled concrete aggregate

Effect of mixing method on the performance of alkali-activated fly ash/slag pastes along with polycarboxylate admixture

Early mechanical properties and strength calculation method of slag-based alkali activated concrete

Effect of binder and activator composition on the characteristics of alkali-activated slag-based concrete

Durability of Alkali activated concrete made using multiple precursors as primary binders

A ternary optimization of alkali-activated cement mortars incorporating glass powder, slag and calcium aluminate cement

Alkali activated cement mixture at ambient curing: Strength, workability, and setting time

Data-driven inverse mix design for sustainable alkali-activated materials

Approach to design sustainable alkali-activated slag recycled aggregate concrete: Mechanical and microstructural characterization

Strength Analysis and Optimization of Alkali Activated Slag Backfills Through Response Surface Methodology

Mechanical Properties of High Early Strength Class C Fly Ash-Based Alkali Activated Concrete

Taguchi-integrated grey relational analysis for multi-response optimization of mix design for alkali-activated concrete

Synthesis of Sustainable OPC‐Blended Geopolymer Concrete: Experimental and Modeling Study

Proposed simplified methodological approach for designing geopolymer concrete mixtures

Recent Advances In Chemical Admixtures For Improving The Workability Of Alkali-Activated Slag-Based Material Systems

Optimisation of an alkali activator solution to enhance the performance of roller-compacted concrete for pavements (RCCP)