Abstract:A shaver cap is a typical thin-walled rotational part, and the processing performance of its torus surface has an important impact on the cutting efficiency, sharpness and working noise of the shaver. Electrochemical face grinding (ECFG) is a promising machining method in the fabrication of difficult-to-cut thin-walled parts. However, the flow field distribution in the interelectrode gap can vary, and the effect of electrochemical levelling can suffer during the electrochemical face grinding of multiple torus surfaces. Moreover, the nonuniform distribution of abrasives and the differences in coequal height can generate severe grinding marks on the torus surfaces. In this work, superimposed linear and circular translational movements were proposed to improve the electrochemical grinding performance of multiple torus surfaces. Based on a simulation of a gas-liquid two-phase flow field, the effects of grinding head rotational speed and superimposed linear and circular translational movements on the flow velocity and void fraction were investigated. Moreover, the variations of machining allowance, flatness and surface roughness on the torus surfaces were experimentally studied. The flow field simulation and experimental results showed that the flow velocity and void fraction were changed periodically in the machining area by superimposing translational movements, which was conducive to eliminating flow field defects and improving the electrochemical levelling performance. Moreover, the fluctuations of electrolyte flow velocity and void fraction in the machining area were small when the circular translational movement was superimposed, and a synergistic effect of dissolution and grinding was noted. The overall flatness of the torus surfaces was only 3.93 μm, the maximum height of the surface roughness profile was 0.797 μm, and there were no obvious grinding marks on the inner and outer torus surfaces under the optimized circular translational parameters.

Flow field simulation and experimental investigation on macro electrolyte jet electrochemical turning of TB6 titanium alloy

Boundary fluid constraints during electrochemical jet machining of large size emerging titanium alloy aerospace parts in gas-liquid flows: Experimental and numerical simulation

Jet Electrochemical Machining of TB6 Titanium Alloy

Effect of Anodic Behavior on Electrochemical Machining of TB6 Titanium Alloy

Simulation Analysis and Experimental Validation of Cathode Tool in Electrochemical Mill-Grinding of Ti6Al4V

Jet Electrochemical Micromilling of Ti-6Al-4V Using NaCl–Ethylene Glycol Electrolyte

Jet electrochemical milling of Ti-6Al-4 V alloy with ultra-high current density

Investigation on Parametric Effects on Groove Profile Generated on Ti1023 Titanium Alloy by Jet Electrochemical Machining

Electrochemical Turning of (TiB + TiC)/TC4 Composites Using a Rectangular Cathode

An Investigation of the Efficient–Precise Continuous Electrochemical Grinding Process of Ti–6Al–4V

Electrolyte Jet Machining of Ti1023 Titanium Alloy Using NaCl Ethylene Glycol-Based Electrolyte

Simultaneous gas electrical discharge and electrochemical jet micromachining of titanium alloy in high-conductivity salt solution

Investigation of inner-jet electrochemical face grinding of thin-walled rotational parts

Electrochemical Properties and Jet Electrochemical Micromilling of (TiB+TiC)/Ti6Al4V Composites in NaCl+NaNO3 Mixed Electrolyte

Improvement of machining quality by using axial supplementary electrolyte in electrochemical cutting with radial electrolyte flushing

Research on electrochemical discharge milling of TC4 titanium alloy

Multi-Physical Field Coupling Simulation and Experiments with Pulse Electrochemical Machining of Large Size TiAl Intermetallic Blade

Study on the Effect of Electrolytes on Processing Efficiency and Accuracy of Titanium Alloy Utilizing Laser and Shaped Tube Electrochemical Machining

Flow field characteristics and experimental research on inner-jet electrochemical face grinding of SUS420J2 stainless steel

Flow field design and experimental investigation of electrochemical trepanning of diffuser with a special structure

Electrochemical machining of titanium alloy blades using optimized cathode with built-in insulators