Abstract:The primary mirror of very large submillimeter-wave telescopes will necessarily be segmented into many separate mirror panels. These panels must be continuously co-phased to keep the telescope wavefront error less than a small fraction of a wavelength, to ten microns RMS (root mean square) or less. This performance must be maintained continuously across the full aperture of the telescope, in all pointing conditions, and in a variable thermal environment. A wavefront compensation segmented mirror sensing and control system, consisting of optical edge sensors, Wavefront Compensation Estimator/Controller Soft ware, and segment position actuators is proposed. Optical edge sensors are placed two per each segment-to-segment edge to continuously measure changes in segment state. Segment position actuators (three per segment) are used to move the panels. A computer control system uses the edge sensor measurements to estimate the state of all of the segments and to predict the wavefront error; segment actuator commands are computed that minimize the wavefront error. Translational or rotational motions of one segment relative to the other cause lateral displacement of the light beam, which is measured by the imaging sensor. For high accuracy, the collimator uses a shaped mask, such as one or more slits, so that the light beam forms a pattern on the sensor that permits sensing accuracy of better than 0.1 micron in two axes: in the z or local surface normal direction, and in the y direction parallel to the mirror surface and perpendicular to the beam direction. Using a co-aligned pair of sensors, with the location of the detector and collimated light source interchanged, four degrees of freedom can be sensed: transverse x and y displacements, as well as two bending angles (pitch and yaw). In this approach, each optical edge sensor head has a collimator and an imager, placing one sensor head on each side of a segment gap, with two parallel light beams crossing the gap. Two sets of optical edge sensors are used per segment-to-segment edge, separated by a finite distance along the segment edge, for four optical heads, each with an imager and a collimator. By orienting the beam direction of one edge sensor pair to be +45 away from the segment edge direction, and the other sensor pair to be oriented -45 away from the segment edge direction, all six degrees of freedom of relative motion between the segments can be measured with some redundancy. The software resides in a computer that receives each of the optical edge sensor signals, as well as telescope pointing commands. It feeds back the edge sensor signals to keep the primary mirror figure within specification. It uses a feed-forward control to compensate for global effects such as decollimation of the primary and secondary mirrors due to gravity sag as the telescope pointing changes to track science objects. Three segment position actuators will be provided per segment to enable controlled motions in the piston, tip, and tilt degrees of freedom. These actuators are driven by the software, providing the optical changes needed to keep the telescope phased.

Receiver control for the Submillimeter Array

A Digital-Receiver for the Murchison Widefield Array

The Control System For The 13.7m Millimeter Wavelength Telescope Equipped With Multibeam Receiver

A Multi-Synchronous Architecture to Control an Array of Networked Siderostats or Telescopes at the Navy Precision Optical Interferometer

Technology Development for the Caltech Submillimeter Observatory Balanced Receivers

Upgrading the Submillimeter Array: wSMA and beyond

A 9-Beam 2SB Receiver for Millimeter-Wave Radio Astronomy

Distributed Control Software for the Active Surface System of Tian-ma Radio Telescope

Signal Processing Firmware for the Low Frequency Aperture Array

The CRS: a scalable full-stack control system for Microwave Kinetic Inductance Detectors

The Real-Time Distributed Control of the Virgo Interferometric Detector of Gravitational Waves

The Simons Observatory: Antenna control software integration and implementation

A Multi-channel Signal Acquisition and Switching Control System Design Based on Remote Operations

Readout System for Frequency-Division Multiplexing Superconducting Detector Arrays

Wavefront Compensation Segmented Mirror Sensing and Control

A scalable and reconfigurable industrial-grade Slow Control System for SABRE-South Dark matter experiment

SLAC Microresonator Radio Frequency (SMuRF) Electronics for Read Out of Frequency-Division-Multiplexed Cryogenic Sensors

Phase synchronisation system receiver module for the Mid-Frequency Square Kilometre Array

A multibeam 2SB SIS receiver at 3mm wavelength

Digital Frequency Domain Multiplexer for mm-Wavelength Telescopes

Highly-multiplexed microwave SQUID readout using the SLAC Microresonator Radio Frequency (SMuRF) electronics for future CMB and sub-millimeter surveys