Abstract:Determining the mechanical characteristics of rocks is crucial in various civil engineering sectors. Traditionally, the mechanical properties of rocks are determined through on-site and laboratory tests carried out during geotechnical surveys. However, these extensive surveys require considerable time and resources. In contrast, hyperspectral remote sensing techniques offer a rapid and simple means to determine the mineral composition and crystallographic structure of rocks. These features, in turn, influence the rocks' mechanical properties. This study focuses on characterizing the mechanical properties of carbonate rocks in a laboratory setting, using hyperspectral sensors. Approximately 150 cylindrical carbonate rock samples, spanning a wide strength range, were collected from diverse Israeli rock outcrops. Employing a point spectrometer (0.4 to 2.5 μm) and a spectral image sensor (8.0 to 12.0 μm), we captured samples' light reflections and spectral emissivity. Mechanical attributes, including density, porosity, water absorption, and uniaxial compressive strength (UCS), were measured. Advanced data mining techniques identified statistical correlations between hyperspectral signatures and mechanical properties, pinpointing key wavelengths for prediction. The developed models exhibited excellent predictability for the specified properties, attributing accuracy to discernible mineralogy and internal crystalline structure through spectroscopy. However, predicting UCS showed slightly weaker results due to influences from internal flaws not entirely reflected in spectroscopic data. Nonetheless, outcomes regarding rock UCS were deemed satisfactory. These findings open avenues for non-destructive tools in assessing the mechanical properties of rocks in quarrying operations.

What problem does this paper attempt to address?

The problem that this paper attempts to solve is that in rock mechanics and engineering geology, the traditional methods for evaluating the mechanical properties of carbonate rocks are time - consuming and costly. Specifically, the paper explores how to use spectral techniques (reflectance and emissivity spectra in the range of 0.4 to 12 μm) to rapidly and non - destructively predict the mechanical properties of carbonate rocks, such as density, porosity, water absorption rate and uniaxial compressive strength (UCS). Through this method, researchers hope to reduce the dependence on field and laboratory tests, thereby improving the evaluation efficiency and accuracy. ### Background of the Paper Traditional methods for evaluating rock mechanical properties mainly rely on field and laboratory tests. These methods are not only time - consuming but also costly. In addition, due to sampling bias and limited field access, these methods have many limitations in practical applications. In contrast, hyperspectral remote sensing technology can quickly and easily determine the mineral composition and crystal structure of rocks, and these characteristics directly affect the mechanical properties of rocks. ### Research Objectives The main objective of this study is to characterize the mechanical properties of carbonate rocks using hyperspectral sensors (in the range of 0.4 to 12 μm) under laboratory conditions. Specifically, the research team collected about 150 cylindrical carbonate rock samples, covering a wide range of strength, and used a point spectrometer (0.4 to 2.5 μm) and a spectral image sensor (8.0 to 12.0 μm) to capture the light reflection and spectral emissivity of the samples. Subsequently, the density, porosity, water absorption rate and uniaxial compressive strength (UCS) of the samples were measured. ### Main Methods 1. **Sample Collection and Preparation**: 150 cylindrical carbonate rock samples were collected from multiple rock formations in Israel, with a diameter of 54 mm and a length of 110 mm. 2. **Spectral Measurement**: The surface reflectance and emissivity spectra of the samples were measured using an ASD spectroradiometer (0.4 to 2.5 μm) and a Telops Hyper - Cam hyperspectral camera (8.0 to 12.0 μm). 3. **Mechanical Property Measurement**: The density, porosity, water absorption rate and uniaxial compressive strength (UCS) of the samples were measured. 4. **Data Processing and Analysis**: The PARACUDA - II® data mining engine was used for data processing, including outlier detection, pre - processing and model development. A prediction model between spectral features and mechanical properties was established through the partial least squares regression (PLSR) algorithm. ### Main Results 1. **Distribution of Mechanical Properties**: The experimental results show that the dry density of most carbonate rock samples is about 2.6 g/cm³, which is in line with the characteristics of typical carbonate rocks. The mechanical properties of different lithologies vary significantly. For example, chalk has a lower strength and a higher water absorption rate, while limestone and dolomite have a higher strength and a lower water absorption rate. 2. **Spectral Features**: In the VNIR - SWIR (0.4 to 2.5 μm) and LWIR (8.0 to 12.0 μm) ranges, samples of different lithologies exhibit different absorption characteristics. For example, carbonate minerals have an obvious absorption peak near 2.33 μm. 3. **Prediction Model**: The established prediction model performs well in predicting density, porosity, water absorption rate and uniaxial compressive strength (UCS). In particular, the prediction models for density and porosity have a high accuracy (R² are 0.97 and 0.99 respectively), while the prediction model for UCS is slightly weaker (R² is 0.89). ### Conclusions This study successfully demonstrates the feasibility of using hyperspectral remote sensing technology to predict the mechanical properties of carbonate rocks. This method not only improves the evaluation efficiency, but also provides a non - destructive tool for engineering geologists, which is helpful for improving the rock quality assessment in quarry operations. However, the prediction results of UCS are affected by internal defects, so further verification and improvement are still required in practical applications.

Predicting Mechanical Properties of Carbonate Rocks Using Spectroscopy Across 0.4–12 μm

Mechanical Characterization of Main Minerals in Carbonate Rock at the Micro Scale Based on Nanoindentation

Machine learning for prediction of the uniaxial compressive strength within carbonate rocks

Controls on mechanical properties of carbonate mudstone: Insights from non-destructive techniques and geochemical data

Quantitative Estimation of Carbonate Rock Fraction in Karst Regions Using Field Spectra in 2.0–2.5 Μm

Estimation of Young's modulus for rocks using a non-invasive CSAMT method

Numerical estimation of carbonate rock properties using multiscale images

Prediction of uniaxial compressive strength of carbonate rocks from nondestructive tests using multivariate regression and LS-SVM methods

Estimation of the dolomite content of carbonate rock outcrops based on spectral knowledge and machine learning

Size Effect on Pore-Scale Variables and Heterogeneous Pore-Network Characteristics in Carbonate Rocks

TWO-DIMENSIONAL IMAGING OF ELASTIC PROPERTIES OF ROCK CORE SAMPLES FROM MEASUREMENTS OF ANGLE-DEPENDENT ULTRASONIC REFLECTION COEFFICIENTS

Model tree approach for predicting uniaxial compressive strength and Young’s modulus of carbonate rocks

Computing heterogeneous core sample velocity using Digital Rock Physics: A multiscale approach

Framework for Bayesian Assessment of Factors that Impact Rock Mechanical Response

Predicting the strength, density, and porosity of rocks from roll crusher tests

Mechanical and Physical Based Artificial Neural Network Models for the Prediction of the Unconfined Compressive Strength of Rock

Predictive Soft Computing Methods for Building Digital Rock Models Verified by Positron Emission Tomography Experiments

Machine Learning Assisted Prediction of Porosity and Related Properties Using Digital Rock Images

Micro-Raman spectroscopic analysis on natural carbonates: linear relations found via biaxial plotting of peak frequencies for cation substituted species

Multiscale Hierarchical Analysis of Rock Mass and Prediction of Its Mechanical and Hydraulic Properties

Predicting the compressive strength of tight sandstone based on the low field NMR and pseudo-triaxial compression measurements