Abstract:This work focused on the verification of the electrical parameters and the durability of side connectors installed in glass–glass photovoltaic modules. Ensuring the safe use of photovoltaic modules is achieved, among others, by using electrical connectors connecting the PV cell circuit inside the laminate with an external electric cable. In most of the cases for standard PV modules, the electrical connector in the form of a junction box is attached from the back side of the PV module. The junction box is glued to the module surface with silicone where the busbars were previously brought out of the laminate through specially prepared holes. An alternative method is to place connectors on the edge of the module, laminating part of it. In such a case, the specially prepared "wings" of the connector are tightly and permanently connected using laminating foil, between two glass panes protecting against an electrical breakdown. Additionally, this approach eliminates the process of preparing holes on the back side of the module, which is especially complicated and time-consuming in the case of glass–glass modules. Moreover, side connectors are desirable in BIPV applications because they allow for a more flexible design of installations on façades and walls of buildings. A series of samples were prepared in the form of PV G-G modules with side connectors, which were then subjected to testing the connectors for the influence of environmental conditions. All samples were characterized before and after the effect of environmental conditions according to PN-EN-61215-2 standards. Insulation resistance tests were performed in dry and wet conditions, ensuring full contact of the tested sample with water. For all modules, before being placed in the climatic chamber, the resistance values were far above the minimum value required by the standards, allowing the module to be safely used. For the dry tests, the resistance values were in the range of GΩ, while for the wet tests, the obtained values were in the range of MΩ. In further work, the modules were subjected to environmental influences in accordance with MQT-11, MQT-12, and MQT-13 and then subjected to electrical measurements again. A simulation of the impact of changing climatic conditions on the module test showed that the insulation resistance value is reduced by an order of magnitude for both the dry and wet tests. Additionally, one can observe visual changes where the lamination foil is in contact with the connector. The measurements carried out in this work show the potential of side connectors and their advantage over rear junction boxes, but also the technological challenges that need to be overcome.

Photovoltaic Cable Connectors: A Comparative Assessment of the Present State of the Industry

Identifying PV Module Mismatch Faults by a Thermography-Based Temperature Distribution Analysis

Impact of environmental variables on the degradation of photovoltaic components and perspectives for the reliability assessment methodology

Influence of Environmental Conditions on the Electrical Parameters of Side Connectors in Glass–Glass Photovoltaic Modules

Review of Mismatch Mitigation Techniques for PV Modules

Microstructure Evaluation of Photovoltaic Solar Panel’s Interconnection: A Review

Towards validation of combined-accelerated stress testing through failure analysis of polyamide-based photovoltaic backsheets

Laboratory and Field Evaluation of Connectors and Other Accessories for Aluminum Conductors in Severe Marine Environments

Reliability of Commercial TOPCon PV Modules—An Extensive Comparative Study

Mechanism Characterization and Nondestructive Inspection Method of Thermal Degradation Faults in EPDM Cable Termination

Partial Discharge Behavior of 220 Kv Prefabricated Cable Termination Induced by Inadequate Interface Pressure

Thermo-mechanical behavior assessment of smart wire connected and busbarPV modules during production, transportation, and subsequent field loading stages

PV Modules and Their Backsheets -- A Case Study of a Multi-MW PV Power Station

Degradation analysis of field-exposed photovoltaic modules with non-fluoropolymer-based backsheets

Interface Damages of Electrical Insulation in Factory Joints of High Voltage Submarine Cables

The Insulation of HVDC Extruded Cable System Joints. Part 1: Review of Materials, Design and Testing Procedures

Failure Analysis Capabilities for PV Systems

Failure analysis of polymeric outdoor insulators used in HVDC converter stations

Non-Destructive Failure Detection and Visualization of Artificially and Naturally Aged PV Modules

Dielectric loss and partial discharge test analysis of 10 kV XLPE cable

A Reliability and Risk Assessment of Solar Photovoltaic Panels Using a Failure Mode and Effects Analysis Approach: A Case Study