Abstract:Ultrafiltration hollow-fiber membranes were prepared from polyetherimide (PEI) with a wet spinning method. The effects of N,N-dimethylacetantide (DMAc) as a solvent additive in the internal coagulant and acetic acid as a non-solvent additive in the dope solution on the morphologies and performances of the membranes were investigated. The influences of PEI dope concentration on membrane morphologies and properties were also studied. Scanning electron microscopy (SEM) indicates that the addition of DMAc into the internal coagulant changes the inner fiber surface from a dense skin layer to a porous structure. However, the pure water flux of the membrane decreases with the increase of DMAc content. On the other hand, the addition of acetic acid into the casting solution promotes the spinodal demixing of the membratte-forming system and suppresses the macrovoid formation in the membrane. A nodular structure forms in the fiber skin layer. With increasing acetic acid content, the pure water flux of the membrane increases about 4-fold and the solute retention shows a slight decrease. The mechanical properties can also be improved slightly by this additive. The thermal resistance of the PEI ultrafiltration membranes prepared in this work was examined by hot water treatment at 80 degrees C. No change was observed in the permeation performance of the membranes, while the study of mechanical properties shows that the elongation-at-break of the membrane decreases slightly. PEI was sulfonated by chlorosulfonic acid (CSA) in 1,2-dichloroethane. With the increase of the molar ratio of CSA to PEI repeat unit and/or reaction time, the ion-exchange capacity (IEC) of the sulfonated polyetherimide (SPEI) increases accordingly. Water uptake test and contact angle measurements show that the hydrophillicity of the SPEI increases with the increase of the IEC. Polyetherimide/sulfonated polyetherintide (PEI/SPET) ultrafiltration hollow-fiber membranes were also prepared with a dry-wet phase inversion method and SPEI was used as a polymer additive. SEM study reveals that the addition of SPEI induces the formation of nodular structure and suppresses the formation of finger-like macrovoids. With the increase of air-gap distance, it was found that the number of micropores formed in the outer fiber surface and the pore size increased. On the other hand, the pure water flux of the membrane reaches a maximum and then decreases, while the solute retention decreases at first and then levels off at longer air-gap. Based on the filtration of bovine serum albuntin (BSA) solution, it was found that the use of SPEI in the blend membranes increased their hydrophilicity.

Low-pressure air plasma-assisted acrylic grafted polyetherimide ultrafiltration membranes with excellent oil-water separation and high anti-fouling performances

Free radical graft polymerization of hydroxyethyl methacrylate and acrylic acid on polyetherimide membrane surface via redox system to improve anti-fouling and oil resistance performance

Plasma etching assisted fabrication of PDA/PEI modified PVDF membranes for oil/water emulsion separation

Preparation and performance of acrylic acid grafted PES ultrafiltration membrane via plasma surface activation

Achieving highly effective non-biofouling performance for polypropylene membranes modified by UV-induced surface graft polymerization of two oppositely charged monomers.

Towards Improved Antifouling Ability and Separation Performance of Polyethersulfone Ultrafiltration Membranes Through Poly(ethylenimine) Grafting

High Efficiency and Flexible Construction of Hydrophilic Polymer Brushes on Polyether Ether Ketone Hollow-Fiber Membrane Surface for Improving Permeability Separation, and Anti-Fouling Performances

Ionic liquid‐induced deep grafting of polyelectrolyte to reform polyamide layer for antifouling nanofiltration membrane

Plasma Graft Polymerization and Surface-Initiated Atom Transfer Radical Polymerization: Characteristics of Low-Fouling Membranes Obtained by Surface Modification with Poly(2-methoxyethyl Acrylate)

Antifouling Performance of Poly(lysine Methacrylamide)-Grafted PVDF Microfiltration Membrane for Solute Separation

Preparation of antifouling TFC RO membranes by facile grafting zwitterionic polymer PEI-CA

The preparation of antifouling ultrafiltration membrane by surface grafting zwitterionic polymer onto poly(arylene ether sulfone) containing hydroxyl groups membrane

Surface Antifouling Modification on Polyethylene Filtration Membranes by Plasma Polymerization

Perfluoro-functionalized polyethyleneimine that enhances antifouling property of nanofiltration membranes

Polytetrafluoroethylene hollow fiber membranes with thru hydrophilic channels for enhancing water transfer and anti-oil-fouling properties

Hydrophilic modification of poly(phthalazine ether sulfone ketone) ultrafiltration membranes by the surface immobilization of poly(ethylene glycol) acrylates

Improvement of the Antifouling Characteristics for Polypropylene Microporous Membranes by the Sequential Photoinduced Graft Polymerization of Acrylic Acid

Stable fouling resistance of polyethylene (PE) separator membrane via oxygen plasma plus zwitterion grafting

Enhanced Fouling-Resistance Performance of Polypropylene Hollow Fiber Membrane Fabricated by Ultrasonic-Assisted Graft Polymerization of Acrylic Acid

Preparation And Performance Of Ultrafiltration Membranes From Polyetherimide And Its Sulfonated Derivatives

Super-hydrophilic Polyetherimide Membrane with Surface Amino Exposed for Highly Efficient Oil–Water Separation