Abstract: We show how to eliminate the error caused by an incorrectly modeled boundary in electrical impedance tomography (EIT). In practical measurements, one usually lacks the exact knowledge of the boundary. Because of this the numerical reconstruction from the measured EIT data is done using a model domain that represents the best guess for the true domain. However, it has been noticed that the inaccurate model of the boundary causes severe errors for the reconstructions. We introduce a new algorithm to find a deformed image of the original isotropic conductivity based on the theory of Teichmuller spaces and implement it numerically.
What problem does this paper attempt to address?
This paper aims to solve the problem of how to efficiently synthesize carbon nanostructures on Ni - and Co - loaded MCM - 41 mesoporous catalysts through the gas - phase pyrolysis method. Specifically, the researchers hope to improve the yield and quality of carbon nanotubes, carbon nanowires and other carbon nanostructures by optimizing the catalyst preparation method and reaction conditions.
### Research Background and Problems
Carbon nanotubes have broad application prospects in electronic devices such as scanning probes, sensors, and field emitters due to their unique physical and chemical properties. In recent years, the method of synthesizing carbon nanostructures by pyrolyzing hydrocarbons (such as methane, acetylene, etc.) has been widely used, and in particular, the catalytic process can significantly improve the yield of single - layer and multi - layer carbon nanotubes.
However, traditional catalyst preparation methods (such as the impregnation method) have some limitations, for example, the uneven distribution of metal particles, resulting in lower growth efficiency of carbon nanostructures. Therefore, the researchers explored the use of mesoporous silica (such as MCM - 41) as a carrier and improved the catalyst preparation method by chemisorbing volatile metal acetylacetonates (such as Ni(acac)₂ and Co(acac)₂).
### Research Objectives
The main objectives of this study are:
1. **Utilize the advantages of MCM - 41 mesoporous materials**: MCM - 41 has a uniform pore size and a large specific surface area, which helps to improve the dispersibility and activity of the catalyst.
2. **Optimize the catalyst preparation process**: Through chemisorbing metal acetylacetonates and performing a reduction treatment, uniformly distributed metal nanoparticles are formed.
3. **Study the formation of carbon nanostructures under different conditions**: By controlling the reaction temperature, time, and atmosphere, observe the formation of carbon nanotubes, carbon nanowires, and amorphous carbon particles.
### Experimental Design
The experiment is divided into three main steps:
1. **Modify the MCM - 41 carrier**: Chemisorb MCM - 41 with metal acetylacetonates (Ni(acac)₂ or Co(acac)₂) in a nitrogen flow.
2. **Reduction of metal nanoparticles**: Heat and reduce the modified MCM - 41 in a mixed atmosphere of hydrogen and argon to form metal nanoparticles.
3. **Pyrolysis reaction of acetylene**: Conduct the pyrolysis reaction of acetylene at 700 °C to deposit carbon nanostructures.
### Results and Discussion
Observation by transmission electron microscopy (TEM) shows that when using a nickel catalyst, the outer diameter of the formed carbon nanotubes is 10 - 35 nm, and the length is 0.4 - 0.7 µm; when using a cobalt catalyst, the outer diameter of the carbon nanotubes is 35 - 52 nm, and the length is 0.4 - 1.5 µm. In addition, a small amount of carbon fibers with a diameter of 50 - 70 nm and a length of 1.4 - 2.5 µm were also observed. Research indicates that the growth of carbon nanostructures mainly occurs at the positions where metal nanoparticles are formed, that is, on the outer surface of the carrier or at the damaged pore walls.
### Conclusions
This study has successfully developed a method of preparing highly efficient carbon nanostructure catalysts by chemisorbing metal acetylacetonates and reducing in a hydrogen atmosphere. By optimizing the reaction conditions, the synthesis of high - yield carbon nanotubes, carbon nanowires, and amorphous carbon particles has been achieved.
\[
\text{Summary formula:}
\]
- Specific surface area \( S_{sp}=905 \, m^{2}/g \)
- Total pore volume \( V_{tot} = 0.87 \, cm^{3}/g \)
- Average pore diameter \( d = 39 \, \text{\AA} \)
These results provide new ideas and technical support for the large - scale synthesis of carbon nanostructures.