Abstract:<p>As it is usually operating in bad working conditions and subjected to the severe interference from diverse paths, internal faults of the hydraulic valve are difficult to be detected using conventional hydraulic testing technology (such as relying on pressure sensors or flow sensors). Moreover, the information collected from a single sensor may not provide accurate diagnostic evidence or a complete description on faults of hydraulic valves, even though employing intelligent fault diagnosis methods. Therefore, a two-stage multi-sensor information fusion method is proposed, including the fault feature fusion and the decision-making information fusion. The aim is to realize the diagnosis on internal faults of hydraulic directional valves using the vibration signal analysis method instead of conventional hydraulic testing ones. The method is mainly divided into three steps. First, the noise reduction of the vibration information collected by multiple acceleration sensors is done using ensemble empirical mode decomposition (EEMD) and Teager-Kaiser energy operator (TEO), so that fault features are more obvious. Then, multi-class fault features including the severity and the location of the wear are extracted from the preprocessing signals to form the original feature set. Second, combined with feature ranking and subset selection based on euclidean distance (FRSSED) and maximum relevance minimum redundancy (mRMR) feature selection method, the statistical features extracted from multiple sensor signals are optimized to form the optimal feature subset. This is the first-level information fusion concerned with fault feature information fusion. In the third step, based on Dempster-Shafer (DS) evidence theory and convolutional neural network (CNN), decision-making information is fused (called second-level information fusion) to obtain the final diagnosis results. A hydraulic test bench is built to test different failure valves. Experimental results indicate that this method is effective in extracting the fault features from multi-sensor signals and detecting the fault states including severity and location of internal wear of the hydraulic valve.</p>

What problem does this paper attempt to address?

The problem that this paper attempts to solve is the difficulty in detecting internal faults of hydraulic directional valves under harsh working conditions. Traditional hydraulic testing techniques (such as relying on pressure sensors or flow sensors) are usually not very effective in detecting internal faults of hydraulic valves, especially for the diagnosis of fault types, severity and location. In addition, the information collected by a single sensor may not provide an accurate basis for diagnosis or a complete description of the fault, even when using intelligent fault diagnosis methods. Therefore, the paper proposes a two - stage multi - sensor information fusion method, aiming to achieve the diagnosis of internal faults of hydraulic directional valves through vibration signal analysis methods instead of traditional hydraulic testing methods. Specifically, the paper aims to solve the above problems in the following ways: 1. **Noise reduction**: Use Ensemble Empirical Mode Decomposition (EEMD) and Teager - Kaiser Energy Operator (TEO) to perform noise reduction processing on the vibration information collected by multiple acceleration sensors, making the fault features more obvious. 2. **Multi - class fault feature extraction**: Extract multi - class fault features including wear severity and location from the pre - processed signals to form an original feature set. 3. **Feature selection and optimization**: Combine Feature Ranking and Subset Selection based on Euclidean Distance (FRSSED) and Maximum Relevance Minimum Redundancy (mRMR) feature selection methods to optimize the statistical features extracted from multiple sensor signals to form an optimal feature subset. This is the first - level information fusion, focusing on the fusion of fault feature information. 4. **Decision - making information fusion**: Based on Dempster - Shafer (DS) evidence theory and Convolutional Neural Network (CNN), perform decision - making information fusion (called second - level information fusion) to obtain the final diagnosis result. Through this method, the paper aims to improve the accuracy and reliability of the diagnosis of internal faults of hydraulic directional valves, especially in complex and highly interfering environments.

Fault diagnosis in a hydraulic directional valve using a two-stage multi-sensor information fusion

Hydraulic directional valve fault diagnosis using a weighted adaptive fusion of multi-dimensional features of a multi-sensor

Intelligent Fault Diagnosis of Hydraulic Systems Based on Multi-Sensor Fusion and Deep Learning

Fault diagnosis of the hydraulic valve using a novel semi-supervised learning method based on multi-sensor information fusion

Early Fault Recognition of Pinion Bearing in Main Reducer of Vehicle Using Information Fusion

An Intelligent Fault Diagnosis Approach Based on Dempster-Shafer Theory for Hydraulic Valves

Fault Diagnosis Based On Fusion Of Multi-Channel Observations By Sensors With Independent Component Analysis And Mutual Information

Intelligent Fault Diagnosis of Hydraulic Systems Based on Multisensor Fusion and Deep Learning

A Multi-Output Fault Diagnosis Framework for Hydraulic System Using a CNN-SVM Hierarchical Learning Strategy

Intelligent Fault Diagnosis of Hydraulic Multi-Way Valve Using the Improved SECNN-GRU Method with mRMR Feature Selection

Fault diagnosis of pump truck waterproof valves using multi-sensor high-dimensional time-domain feature expansion map

A hydraulic motor fault diagnosis method based on weighted multi-channel information fusion

Multi-fault diagnosis and fault degree identification in hydraulic systems based on fully convolutional networks and deep feature fusion

Fault diagnosis method of hydraulic system based on multi-source information fusion and fractal dimension

Intelligent fault diagnosis methods for hydraulic components based on information fusion: review and prospects

Rotating Machinery Fault Diagnosis Method Based on Multi-Level Fusion Framework of Multi-Sensor Information

Hydraulic system fault diagnosis decoupling method based on 2D time-series modeling and self-attention fusion

A New Multisensor Information Fusion Technique Using Processed Images: Algorithms and Application on Hydraulic Components

DSmT-based Three-Layer Method Using Multi-Classifier to Detect Faults in Hydraulic Systems

Fault Diagnosis of Hydraulic Components Based on Multi-Sensor Information Fusion Using Improved TSO-CNN-BiLSTM

Fault Diagnosis Method of Waterproof Valves in Engineering Mixing Machinery Based on a New Adaptive Feature Extraction Model