Abstract:A combined finite element analysis and computational fluid dynamics was developed to investigate the discharge characteristics and flow field of pocket damper seals at high pressure (up to 7.2 MPa) and high rotational speed (up to 50,200 r/min) flow condition. At first, the leakage flow rates of the published experimental pocket damper seals with the eight-bladed and eight-pocket were conducted at three different pressure drops and three different rotational speeds, and a comparison between finite element analysis and computational fluid dynamics results, experimental data and computational fluid dynamics results was presented. It showed that the utilized finite element analysis/computational fluid dynamics numerical method has sufficient precision (the maximum relative deviation is less than 1.3%) to predict the leakage flow rate through the pocket damper seals. The importance of taking rotor growth with rotational speed into consideration was made apparent by the rotor growth and leakage results. Then, six pressure ratios and seven rotational speeds were utilized to study the effects of these two factors on the leakage flow characteristics of the pocket damper seals. Numerical simulation results show that the leakage through a pocket damper seals increases with decreasing pressure ratio and asymptotically approach a maximum value corresponding to the choked flow condition when the pressure ratio is small enough (less than 0.26). The leakage flow rate with and without rotor growth included both decrease with the increasing rotational speed. In addition, it is quite necessary to take rotor growth with rotational speed into consideration when the rotational speed is very high (larger than 20,200 r/min) according to the numerical results and the engineering accuracy requirement. The influence of the pressure ratio on the structure of the leakage flow field in seal cavity is negligible. A significant influence of the rotational speed on the flow field in the active cavity has been observed. The circumferential partition wall can significantly decrease the circumferential flow in active cavity of the pocket damper seals.

Investigation of the leakage in the flow distribution pair of radial piston hydraulic motors through CFD analysis and experiments

Analysis of force and leakage in water hydraulic motor' s piston pairs

Modelling and Experiment Study on Fluid Character of Axial Piston Pump

Analysis of the Flow Dynamics Characteristics of an Axial Piston Pump Based on the Computational Fluid Dynamics Method

Volumetric Efficiency in Motor-Driven Two-Dimensional Piston Pumps with Leakage and Reverse Flow under High Pressure

A Numerical and Experimental Investigation of Parametric Effect on Flow Ripple

Investigation on the Energy Exchange Characteristics of the Regenerative Flow Pump in an Automobile Fuel System

Experimental Study on the Influence of the Rotating Cylinder Block and Pistons on Churning Losses in Axial Piston Pumps

58812 ANALYSIS OF THE PISTON/CYLINDER PAIR OF AXIAL PISTON PUMP BASED ON VIRTUAL PROTOTYPE(Fluid-Structure Interaction in MBS)

New Analytical Leakage Models for Tribological Interfaces in Axial Piston Pumps

A Thermohydrodynamic Analysis of the Self-Lubricating Bearings Applied in Gear Pumps Using Computational Fluid Dynamics Method

Investigation of leakage within an external gear pump with new decompression slots: numerical and experimental study

Numerical investigations on the leakage flow characteristics of pocket damper labyrinth seals

Experimental and Numerical Study on the Formation Mechanism of Flow Field in a Side-Ported Rotary Engine Considering Apex Seal Leakage

Study on the Leakage of the Continuous Rotary Electro-hydraulic Servo Motor

Leakage Loss Study of a Synchronal Rotary Multiphase Pump with a Full Range of Inlet Gas Volume Fractions

Numerical Investigation on Effects of Leakage Flow on the Aerodynamic Performance of Turbine Stages

Research and Analysis on the Radial Clearance Leakage for Translational Rotary Compres-sors

Experimental And Numerical Investigations On The Leakage Flow Characteristics Of The Labyrinth Brush Seal

Study on Leakage via the Radial Clearance in a Double Vane Ellipse Rotor Compressor

Influence of Internal Flow on the Performance of High-Speed Centrifugal Pumps with a Fully Sealed Structure