Abstract:Nowadays, pumps of different size are needed for a great variety of purposes. In the past, both computational fluid dynamics (CFD) and experimental flow visualization were performed to reveal flow characteristics within centrifugal pumps, to examine a specific design and to guide design improvement (see Burgreen et al. 1996, 2000). Li et al. (2007) studied the interior viscous flow in a mini pump with an asymmetric axis using CFD and PIV (particle image velocimetry) for improvement of the pump design. Matsui et al. (2002) adopted the the k-ω model in the CFD simulation for a centrfugal pump, and the computational grid system only consisted of one flow passage for LDV (laser Dopler velocimetry) test impeller. Byskov et al. (2003a) and Pedersen & Larsen (2003 b) investigated the flow inside the rotating passages of a six-bladed shrouded centrifugal pump impeller using LES simulation and PIV and LDV measurements. The velocities predicted with LES were in good agreement with the experimental data. The two RANS simulations were, however, not able to predict this complex flow field. It was thus found that using LES for analyzing the flow field in centrifugal pumps could shed light on basic fluid dynamic with a satisfactory accuracy compared to experiments. A transient simulation was used to study the effects of pulsatile blood flow due to the heartbeat through blood pumps by Song et al. (2003). The microsized geometry of the pump made the choice of turbulence models significant for the accuracy of calculation. The comparison showed that the k-ω model gave better predictions of the shear level within the near wall regions than the k-e model. Guleren and Pinarbasi (2004) indicated that the stallcell size extended from one to two diffuser passages. Comparisons of the computational results with experimental data were made and showed good agreement. The unsteady flow in a low specific speed radial diffuser was simulated by the CFD code CFX-10 by Feng et al. (2009). The PIV and LDV measurements had been conducted to validate the CFD results. Both the phase-averaged velocity fields and the turbulence fields obtained from different methods are presented and compared. In this study, in order to get more information about the internal flow of a centrifugal pump, both experimental measurement and numerical simulation are engaged. A centrifugal model pump test rig is built for PIV measurement. The test, involving the technology of index match and fluorescent, is for acquiring flow pattern in a fixed rotational speed, the velocity distribution of the flow field are thus obtained. And, the RANS (Reynolds

Capabilities of Numerical Simulation of Multiphase Flows in Centrifugal Pumps using Modern CFD Software

Numerical Simulation on Internal Flow in the Screw Centrifugal Pulp Pump

Numerical Simulation of the Cavitation Characteristics of A Mixed-Flow Pump

Performance Prediction of Centrifugal Pump Based on the Method of Numerical Simulation

Analysis of flow characteristics in the volute casing of centrifugal pump based on numerical simulation

Contemporary Approach for Simulation and Computation of Fluid Flows in Centrifugal Hydromachines

State of the Art on Two-Phase Non-Miscible Liquid/Gas Flow Transport Analysis in Radial Centrifugal Pumps Part C: CFD Approaches with Emphasis on Improved Models

Numerical Simulation of Flow in Centrifugal Pump with Complex Impeller

Development of a Numerical Approach for the CFD Simulation of a Gear Pump under Actual Operating Conditions

The 3D Numerical Simulation and Analysis on Internal Flow Field in Centrifugal Pump

Numerical Simulation and Analysis of Cavitation Flows in a Double Suction Centrifugal Pump

Numerical Simulation of Gas–Liquid Two-Phase Flow Characteristics of Centrifugal Pump Based on the CFD–PBM

Transient numerical simulation for solid-liquid flow in a centrifugal pump by DEM-CFD coupling

Liquid-vapor two-phase flow in centrifugal pump: Cavitation, mass transfer, and impeller structure optimization

Numerical simulation of three-dimensional turbulent flow in a centrifugal pump impeller

Numerical simulation of cavitation in the flow path of a reversible hydraulic machine for a head up to 250m

Numerical Study of the Hydrodynamics of an External Gear Pump

Numerical Simulation and Experimental Validation of the Flow Field in Axial Flow Pump

Numerical Simulation on the Steady and Unsteady Internal Flows of a Centrifugal Pump

Numerical Simulation of Fine Particle Solid-Liquid Two-Phase Flow in a Centrifugal Pump

Numerical simulation of gas-liquid two-phase turbulent flows through a centrifugal impeller